Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 9 › Lesson 9.2

9.2 General plane motion and instantaneous centre

Engineering Mechanics Chapter 9: Plane motion of rigid bodies Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Recognise translation, rotation about a fixed axis and general plane motion of a rigid body.
  • Relate the velocities of two points of a body by v_B = v_A + ω × r_B/A and apply the rolling-without-slip conditions v_G = r ω and a_G = r α.
  • Locate the instantaneous centre of zero velocity and use it to find velocities in rolling wheels, sliding bars and slider-crank mechanisms.

Theory

In plane motion every point of a rigid body moves in a plane parallel to one reference plane. Three kinds occur. In translation every line of the body keeps its direction, so all points have the same velocity and acceleration; a load hanging level on a crane trolley translates. In rotation about a fixed axis (lesson 9.1) one line of points stays at rest. General plane motion is everything else: a rolling roller drum, a plank sliding down a wall, the connecting rod of a pump or a compressor.

Any general plane motion can be split into a translation with a chosen reference point A plus a rotation about A. The rotation part is the same whatever point is chosen, so the body has one angular velocity ω. If the vector from A to B is r_B/A, then because the distance AB cannot change, B can only move relative to A on a circle round A: v_B = v_A + ω × r_B/A, and the relative speed is ω times AB, at right angles to AB. Differentiating once more gives a_B = a_A + α × r_B/A − ω² r_B/A, the tangential and normal relative terms of lesson 9.1.

I (v = 0)v2v√2 vωv_P = ω · IP, perpendicular to IPIndiacon original, not to scale
Figure 9.2: Rolling without slip: the contact point I is the instantaneous centre, so the centre moves at v, the top at 2v and a point level with the axle at √2 v. Indiacon original, not to scale.

At any instant there is one point, on the body or on its imagined extension, whose velocity is zero. This is the instantaneous centre of zero velocity, I. At that instant the body moves as if rotating about I, so every point P has speed ω × IP, directed at right angles to the line IP. I is found by drawing perpendiculars to two known velocity directions; where they meet is I. If the two perpendiculars are parallel the body is translating at that instant and ω = 0. I is only a velocity centre: its own acceleration is not zero, so it must not be used for accelerations.

For a wheel or drum rolling without slipping on a fixed surface, the contact point has zero velocity and is the instantaneous centre. The centre therefore moves at v_G = r ω, the top point at 2 r ω, and differentiating, a_G = r α. A road roller, a crawler idler or a pipe rolled along a trench all follow these relations, and the same idea gives the speed of a plank or precast panel sliding with one end on a wall and one on the floor.

Derivation

  1. Let A and B be two points of a rigid body with r_B = r_A + r_B/A, where the length |r_B/A| is constant.
  2. Differentiate: v_B = v_A + d(r_B/A)/dt. A vector of constant length that turns with the body changes only by rotation, so d(r_B/A)/dt = ω × r_B/A.
  3. Hence v_B = v_A + ω × r_B/A, with |ω × r_B/A| = ω · AB at right angles to AB.
  4. Differentiate again: a_B = a_A + α × r_B/A + ω × (ω × r_B/A) = a_A + α × r_B/A − ω² r_B/A in plane motion.
  5. Instantaneous centre: put v_I = 0, so v_P = ω × r_P/I for every point P; its speed is ω · IP, perpendicular to IP.
  6. Rolling without slip: the contact point C has v_C = 0, so v_G = ω r; differentiating with r constant gives a_G = α r.
  7. Sliding bar of length L with ends on a wall and floor: x² + y² = L², so x ẋ + y ẏ = 0 and ẏ = −x ẋ / y, which matches the result from the instantaneous centre.
Formulas, symbols and SI units
  • v_B = v_A + ω × r_B/A; relative speed ω · AB (m/s), perpendicular to AB
  • a_B = a_A + α × r_B/A − ω² r_B/A (m/s²)
  • Instantaneous centre I: v_P = ω · IP, perpendicular to IP
  • Rolling without slip: v_G = r ω, a_G = r α; top point 2 r ω; contact point 0
  • Sliding bar with ends on wall and floor: ẏ = −x ẋ / y
  • Slider-crank (crank r, rod l, n = l/r): v_slider = r ω [sin θ + sin 2θ / (2 √(n² − sin² θ))]
Assumptions and limits
  • The body is rigid and moves in one plane.
  • Rolling means no slip at the contact; a slipping wheel has v_G ≠ r ω.
  • The instantaneous centre gives velocities only; accelerations use a_B = a_A + α × r_B/A − ω² r_B/A.
  • Mechanism links are rigid and pins are frictionless for the purpose of kinematics.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; plane kinematics is a part of mechanics. Operating speeds of rollers, crawlers and mechanisms come from equipment data and the relevant machine standards, not from this lesson.

Worked examples

Example 1 (site style)

Problem. A road roller drum of radius 0.6 m rolls without slipping at 1.2 m/s. Find its angular velocity, the speed of the top point and of a point on the rim level with the axle at the front, and the number of turns in 100 m.

  1. Contact point is the instantaneous centre: ω = v_G / r = 1.2 / 0.6 = 2 rad/s (19.1 rev/min).
  2. Top point: distance from I = 2r = 1.2 m, speed = 2 × 1.2 = 2.4 m/s, forwards.
  3. Front point level with the axle: distance from I = √(0.6² + 0.6²) = 0.8485 m, speed = 2 × 0.8485 = 1.697 m/s, directed at 45° below the horizontal (perpendicular to the line from I).
  4. Turns in 100 m = 100 / (2π × 0.6) = 26.53.

Answer. ω = 2 rad/s; top 2.40 m/s; front point 1.70 m/s at 45°; 26.5 turns per 100 m

Example 2 (exam style)

Problem. A 5 m plank leans against a vertical wall. Its foot B is pulled away along the floor at 0.6 m/s. Find the plank's angular velocity, the velocity of the top A and of the midpoint G when B is 3 m from the wall.

  1. Geometry: B = (3, 0), A = (0, 4) since 3² + 4² = 5².
  2. v_B is horizontal, so I lies on the vertical through B; v_A is vertical, so I lies on the horizontal through A. Hence I = (3, 4).
  3. IB = 4 m, so ω = 0.6 / 4 = 0.15 rad/s.
  4. IA = 3 m, so v_A = 0.15 × 3 = 0.45 m/s, downwards. Check: ẏ = −x ẋ / y = −3 × 0.6 / 4 = −0.45 m/s.
  5. G = (1.5, 2); IG = √(1.5² + 2²) = 2.5 m, so v_G = 0.15 × 2.5 = 0.375 m/s, perpendicular to IG.

Answer. ω = 0.15 rad/s; top slides down at 0.45 m/s; midpoint 0.375 m/s

Example 3 (exam style)

Problem. A reciprocating pump has a crank OA = 0.1 m turning at 300 rev/min and a connecting rod AB = 0.4 m; the piston B moves along the line through O. Find the angular velocity of the rod and the piston speed when the crank is at 60° from the inner dead centre.

  1. ω_OA = 2π × 300 / 60 = 31.42 rad/s; v_A = 0.1 × 31.42 = 3.142 m/s, perpendicular to OA.
  2. Positions with O at the origin: A = (0.05, 0.0866); B = (0.05 + √(0.4² − 0.0866²), 0) = (0.4405, 0).
  3. v_A is perpendicular to OA, so I lies on line OA extended; v_B is along the line of stroke, so I lies on the vertical through B. I = (0.4405, 0.4405 tan 60°) = (0.4405, 0.7630).
  4. IA = OI − OA = 0.4405 / cos 60° − 0.1 = 0.7810 m; ω_AB = 3.142 / 0.7810 = 4.022 rad/s.
  5. IB = 0.7630 m; v_B = 4.022 × 0.7630 = 3.069 m/s. Check by the slider-crank formula with n = 4: 0.1 × 31.42 × (0.8660 + 0.8660 / 7.810) = 3.069 m/s.

Answer. ω_AB = 4.02 rad/s; piston speed 3.07 m/s

Step-by-step procedure

  1. Classify the motion: translation, fixed-axis rotation or general plane motion.
  2. Mark two points whose velocity directions are known (a pin on a crank, a slider, a contact point).
  3. Draw perpendiculars to those directions; their intersection is the instantaneous centre I (if parallel, the body translates at that instant).
  4. Find ω from a point of known speed: ω = v_A / IA. Then any point P has speed ω · IP at right angles to IP.
  5. For accelerations, use a_B = a_A + α × r_B/A − ω² r_B/A, never the instantaneous centre; for rolling, use a_G = r α.

Site notes

  • A roller drum's contact patch is momentarily at rest, which is why rolling compacts by pressure and kneading rather than by scraping; slip (spinning drums on wet clay) tears the surface.
  • Crawler tracks run at twice the machine speed over the top run and are at rest on the ground, the same 2 r ω and 0 found for a rolling wheel.
  • When a long plank, ladder or precast element is slid with one end on the ground and the other on a wall or support, the top drops slowly at first and fast at the end; the instantaneous centre shows why, and it is the reason such elements are lowered under control, never let slide.
  • Pumps, compressors and jaw crushers use slider-crank or linkage mechanisms whose piston or jaw speed varies through the stroke; the instantaneous centre gives that speed at any crank angle.
Common mistakes
  • Using the instantaneous centre to find accelerations.
  • Taking the velocity of a point as ω times its distance from the body's centre instead of from I.
  • Forgetting that the contact point of a rolling wheel has zero velocity but a non-zero acceleration (r ω² towards the centre).
  • Assuming v_G = r ω when the wheel is slipping or skidding.
  • Drawing a point's velocity along the line to I instead of perpendicular to it.
Quick check

For a wheel rolling without slip, the speeds of the contact point, centre and top point are 0, v and 2v.

Summary

  • Plane motion = translation of a reference point + rotation with one ω.
  • v_B = v_A + ω × r_B/A.
  • Instantaneous centre: v_P = ω · IP, perpendicular to IP; velocities only.
  • Rolling without slip: v_G = r ω, a_G = r α.

Practice questions

Tap a question to see the answer.

1A car wheel of radius 0.3 m rolls without slip at 54 km/h. Find its angular velocity and the speed of the top of the tyre.

v = 15 m/s; ω = 15 / 0.3 = 50 rad/s; top speed 2 × 15 = 30 m/s.

2A roller drum of radius 0.6 m turns at 30 rev/min without slip. Find the roller's travel speed.

ω = 3.1416 rad/s; v = 0.6 × 3.1416 = 1.885 m/s = 6.79 km/h.

3A 4 m bar has its top A on a smooth wall and foot B on the floor, making 60° with the floor. B moves away at 1 m/s. Find ω and the speed of A.

B = (2, 0), A = (0, 3.464); I = (2, 3.464); ω = 1 / 3.464 = 0.2887 rad/s; v_A = 0.2887 × 2 = 0.5774 m/s downwards.

4What is the velocity of the contact point of a wheel rolling without slipping?

Zero; it is the instantaneous centre of zero velocity.

5A wheel of radius 0.5 m rolls without slip with v_G = 2 m/s and a_G = 1 m/s². Find ω, α and the acceleration of the contact point.

ω = 4 rad/s; α = 2 rad/s²; contact point acceleration = r ω² = 0.5 × 16 = 8 m/s², towards the centre.

6Point A of a body moves at 2 m/s in the +x direction and the body turns at 0.5 rad/s anticlockwise. Find the velocity of point B, 2 m from A in the +y direction.

v_B = v_A + ω × r_B/A = 2 i + 0.5 k × 2 j = 2 i − 1 i = 1 m/s in the +x direction.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.