9.3 Equations of plane motion
After this lesson you should be able to:
- Write the three equations of plane motion of a rigid body, ΣF_x = m a_Gx, ΣF_y = m a_Gy and ΣM_G = I_G α, and the fixed-axis form ΣM_O = I_O α.
- Use the mass moment of inertia, radius of gyration and parallel-axis theorem from lesson 5.5 in kinetics problems.
- Solve hoist drums with hanging loads, bodies rolling down slopes (with the friction needed to prevent slip) and bars pivoting about one end.
Theory
Newton's second law for a particle (lesson 8.1) becomes, for a rigid body, two statements. First, the sum of the external forces equals the total mass times the acceleration of the mass centre G: ΣF = m a_G. The internal forces between particles cancel in pairs, so the mass centre moves as if all the mass were there and all the forces acted on it. Second, the sum of the moments of the external forces about G equals I_G α, where I_G is the mass moment of inertia about an axis through G at right angles to the plane of motion.
I_G plays the same part for rotation that mass plays for translation: it measures resistance to angular acceleration. It depends on how far the mass lies from the axis, I = ∫ r² dm, and is often written I = m k², where k is the radius of gyration. A thin ring of radius r has k² = r², a solid disc or cylinder k² = r²/2, a uniform bar about its centre k² = L²/12. The parallel-axis theorem I_O = I_G + m d² moves it to any parallel axis at distance d.
For rotation about a fixed axis through O the moment equation can be taken about O itself: ΣM_O = I_O α. This is the quickest form for drums, flywheels and bars hinged at one end, because the unknown bearing reaction then drops out. For rolling without slip, the kinematic link a_G = r α from lesson 9.2 adds the third equation; the friction force at the contact is whatever is needed to keep the contact point from slipping, and it must be checked against μ N.
D'Alembert's principle extends naturally: add an inertia force −m a_G at G and an inertia couple −I_G α, and the body may be treated as if in equilibrium, taking moments about any convenient point. Civil uses include the rope tension and load acceleration of a winch whose brake is released, the run-away speed of pipes or rollers on a slope, and the sudden change in the reaction at a hinge when the other support of a beam or panel is removed.
Derivation
- For each particle i of the body: F_i + Σ_j f_ij = m_i a_i, where f_ij are internal forces with f_ij = −f_ji.
- Sum over all particles: the internal forces cancel, so ΣF = Σ m_i a_i = m a_G, by the definition of the mass centre.
- Take moments about G: Σ ρ_i × F_i = Σ ρ_i × m_i a_i. With a_i = a_G + α × ρ_i − ω² ρ_i, the a_G term vanishes (Σ m_i ρ_i = 0) and the ω² term is parallel to ρ_i, leaving Σ m_i ρ_i² α = I_G α. Hence ΣM_G = I_G α.
- Fixed axis through O: a_G = α × r_G − ω² r_G; taking moments about O gives ΣM_O = (I_G + m d²) α = I_O α (parallel-axis theorem).
- Rolling down a slope θ without slip: m g sin θ − F = m a and F r = I_G α = m k² a / r, so a = g sin θ / (1 + k²/r²) and F = m g sin θ (k²/r²) / (1 + k²/r²).
- No slip requires F ≤ μ N = μ m g cos θ, i.e. μ ≥ tan θ (k²/r²) / (1 + k²/r²).
- Hoist drum (rope radius r, drum inertia I) with hanging mass m: m g − T = m a, T r = I α, a = r α give a = m g r² / (m r² + I).
ΣF_x = m a_Gx, ΣF_y = m a_Gy (N)ΣM_G = I_G α (N·m); fixed axis ΣM_O = I_O αI = m k² (kg·m²); I_O = I_G + m d²Ring k² = r²; solid cylinder k² = r²/2; hollow cylinder k² = (r_o² + r_i²)/2; bar about centre L²/12, about end L²/3Rolling down slope θ: a = g sin θ / (1 + k²/r²); μ_min = tan θ (k²/r²) / (1 + k²/r²)Drum with hanging load: a = m g r² / (m r² + I), T = m (g − a)Uniform bar released from horizontal about one end: α = 3g / (2L), pivot reaction = m g / 4
- The body is rigid and moves in a plane of symmetry, so I_G is about the axis normal to that plane.
- Bearing friction and rope mass are neglected unless stated.
- Rolling means no slip; the friction force needed must be checked against μ N.
- Thin-walled pipes are treated as rings (k = r) and thick pipes with k² = (r_o² + r_i²)/2; real pipes with sockets differ slightly.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; the equations of plane motion are principles of mechanics. Hoist braking, crane dynamic factors and pipe-handling rules come from the equipment, crane and safety standards of the relevant subjects, not from this lesson.
Worked examples
Problem. A winch drum of mass 200 kg and radius of gyration 0.3 m carries a rope wound at radius 0.4 m. A 100 kg load hangs from the rope. The brake is released with the load at rest. Neglecting bearing friction, find the load's acceleration, the drum's angular acceleration and the rope tension.
- I = m k² = 200 × 0.3² = 18 kg·m².
- Load: 100 × 9.81 − T = 100 a. Drum: T × 0.4 = 18 α. Rope: a = 0.4 α.
- Substituting: T = 18 a / 0.16 = 112.5 a, so 981 = (100 + 112.5) a and a = 4.6165 m/s².
- α = a / 0.4 = 11.54 rad/s²; T = 100 × (9.81 − 4.6165) = 519.4 N.
- The rope carries only 53 % of the static 981 N while the load runs away; without the drum's inertia the load would fall freely at g.
Answer. a = 4.62 m/s²; α = 11.5 rad/s²; T = 519 N
Problem. A solid concrete roller and an RCC pipe (outer radius 0.6 m, inner radius 0.5 m) are each released from rest on a 10° slope and roll without slipping. Find each acceleration, the speed after 5 m along the slope, and the least friction coefficient needed to prevent slip.
- Solid cylinder k²/r² = 0.5: a = 9.81 sin 10° / 1.5 = 9.81 × 0.17365 / 1.5 = 1.136 m/s²; v = √(2 × 1.136 × 5) = 3.370 m/s.
- μ_min = tan 10° × 0.5 / 1.5 = 0.17633 / 3 = 0.0588.
- Pipe k² = (0.6² + 0.5²)/2 = 0.305 m², k²/r² = 0.305 / 0.36 = 0.8472: a = 9.81 × 0.17365 / 1.8472 = 0.922 m/s²; v = √(2 × 0.922 × 5) = 3.037 m/s.
- Pipe μ_min = 0.17633 × 0.8472 / 1.8472 = 0.0809.
- Both speed up steadily and need very little friction to roll, so even a gentle slope sets them moving: chock pipes and keep rollers braked when parked on a grade.
Answer. Roller 1.14 m/s², 3.37 m/s after 5 m, μ ≥ 0.059; pipe 0.92 m/s², 3.04 m/s, μ ≥ 0.081
Problem. A uniform 6 m steel beam of mass 300 kg rests horizontally on a pin at one end and a prop at the other. The prop is knocked out. Find the beam's angular acceleration and the pin reaction just after release.
- About the pin O: I_O = m L² / 3 = 300 × 36 / 3 = 3600 kg·m².
- ΣM_O = I_O α: m g × L/2 = 300 × 9.81 × 3 = 8829 N·m, so α = 8829 / 3600 = 2.4525 rad/s² (= 3g / 2L).
- At release ω = 0, so a_G is purely tangential: a_G = α L/2 = 7.3575 m/s² downwards (= 3g/4).
- Vertical forces: m g − R = m a_G, so R = 300 × (9.81 − 7.3575) = 735.75 N (= m g / 4).
- Before release the pin carried m g / 2 = 1471.5 N; it drops instantly to a half of that, while the free end falls faster than g.
Answer. α = 2.45 rad/s²; pin reaction drops from 1472 N to 736 N
Step-by-step procedure
- Draw the free-body diagram with all external forces and a kinetic diagram showing m a_G at G and I_G α.
- Choose axes and a positive sense of rotation; write ΣF_x = m a_Gx, ΣF_y = m a_Gy and ΣM_G = I_G α (or ΣM_O = I_O α for a fixed axis).
- Add kinematic links: a = r α for ropes on drums and for rolling without slip; a_G = α × r_G − ω² r_G for fixed-axis rotation.
- Solve the equations together for the accelerations and forces.
- Check assumptions: rope stays taut (T > 0), friction needed is not more than μ N, and signs make sense.
Site notes
- When a winch brake is released, the load's acceleration is reduced only by the drum and gear inertia; heavy loads must never be lowered by releasing the brake and letting the drum run.
- Round bodies such as pipes, drums, rollers and coils need very little friction to roll, as Example 2 shows; stacks are chocked and stored on level ground.
- Removing one support of a beam, panel or precast element changes the other reaction suddenly; the pin reaction falls to a quarter of the weight for a uniform bar, and the free end falls faster than free fall, which is why props are removed only with the element slung.
- A flywheel or crusher rotor with a large I resists changes in speed; it smooths the load on the motor but also needs a strong brake to stop.
- Taking moments about an arbitrary accelerating point and writing ΣM = I α without the m a_G moment term.
- Using the mass m in place of the moment of inertia I in rotation equations.
- Using I_G instead of I_O = I_G + m d² for a fixed axis that does not pass through G.
- Setting friction equal to μ N for a body that rolls without slipping.
- Assuming rope tension equals the hanging weight when the drum is accelerating.
Rolling down a slope: a/(g sin θ) = 1/(1 + k²/r²), so a ring rolls at half, a solid cylinder at two-thirds of the frictionless sliding acceleration.
Summary
- ΣF = m a_G; ΣM_G = I_G α.
- Fixed axis: ΣM_O = I_O α, with I_O = I_G + m d².
- Rolling: a = g sin θ / (1 + k²/r²); check μ ≥ μ_min.
- D'Alembert: add −m a_G and −I_G α and treat as equilibrium.
Practice questions
Tap a question to see the answer.
1A flywheel with I = 50 kg·m² is acted on by a net torque of 200 N·m. Find its angular acceleration.
α = 200 / 50 = 4 rad/s².
2Find the mass moment of inertia of a uniform 12 kg, 2 m bar about one end using the parallel-axis theorem.
I_G = 12 × 2² / 12 = 4 kg·m²; I_end = 4 + 12 × 1² = 16 kg·m², equal to m L²/3.
3A thin-walled pipe rolls without slip down a 30° slope. Find its acceleration.
Ring: a = g sin 30° / 2 = 2.4525 m/s².
4A drum with I = 8 kg·m² running at 600 rev/min is stopped uniformly in 5 s. Find the braking torque.
ω = 62.83 rad/s; α = 12.566 rad/s²; M = 8 × 12.566 = 100.5 N·m.
5A rotor of mass 500 kg has I = 125 kg·m². Find its radius of gyration.
k = √(125 / 500) = 0.5 m.
6A 40 kg solid disc of radius 0.5 m turns on a fixed axle through its centre. A cord wound on its rim is pulled with 100 N. Find α.
I = ½ × 40 × 0.25 = 5 kg·m²; α = 100 × 0.5 / 5 = 10 rad/s².
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.