Indiacon CivilSubscribe

Textbook › Engineering Mechanics › Chapter 10 › Lesson 10.1

10.1 Free undamped vibration of a single-degree system

Engineering Mechanics Chapter 10: Introduction to vibrations Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Model a structure or machine as a single-degree-of-freedom (SDOF) mass-spring system and write its equation of motion m ẍ + k x = 0.
  • Derive and use the natural circular frequency ω_n = √(k/m), the natural frequency f_n = ω_n/2π and the period T = 1/f_n, including the static-deflection form f_n = (1/2π)√(g/δ_st).
  • Find the equivalent stiffness of springs in series and in parallel and of simple members (cantilever column, simply supported beam), and the amplitude of motion from given initial conditions.

Theory

A vibration is a repeated back-and-forth motion about an equilibrium position. It needs two things: a restoring force that pulls the body back when it is displaced, and inertia that carries it past the equilibrium position. In civil engineering the restoring force usually comes from the elastic stiffness of a member (a column, a beam, a soil spring, a set of rubber pads) and the inertia from a mass that is concentrated somewhere convenient (a water tank on a staging, a roof slab, a machine on its mounts).

The simplest model is the single-degree-of-freedom system: one mass m, free to move in one direction x, held by a spring of stiffness k, the force needed per unit displacement (N/m). Displace the mass and let go. The spring pushes back with −k x, Newton's second law gives m ẍ = −k x, and the motion that satisfies this is a sine wave that repeats for ever in the absence of damping. Its rate is fixed by the system alone: ω_n = √(k/m) in rad/s. A stiffer system vibrates faster; a heavier one vibrates more slowly.

mk = 3EI/L³xT = 2π√(m/k)Xm ẍ + k x = 0, ω_n = √(k/m)Indiacon original, not to scale
Figure 10.1: An elevated tank as a single-degree system: the tank mass m on a column of lateral stiffness k = 3EI/L³ swings in a sine wave of period T = 2π√(m/k). Indiacon original, not to scale.

The natural frequency is the most important single number in structural dynamics. It decides whether a footbridge feels lively under people walking, whether a machine foundation will resonate with its motor, and where a building or an elevated tank sits on an earthquake design spectrum. Because ω_n depends on k/m, the same structure has different frequencies when its mass changes: a full water tank vibrates more slowly than an empty one.

The amplitude and the starting point of the sine wave, unlike the frequency, depend on how the motion was started: the initial displacement x₀ and initial velocity v₀. Energy gives a second view: in free undamped vibration the total energy ½ k x² + ½ m ẋ² is constant, swapping between strain energy in the spring at the extreme positions and kinetic energy at the middle. Setting the two maxima equal is Rayleigh's method, which gives ω_n directly and also works for members whose mass is spread out.

Derivation

  1. Free-body diagram of the mass displaced by x from static equilibrium: the spring force is −k x (gravity and the static spring force cancel at equilibrium, so they drop out).
  2. Newton's second law: m ẍ = −k x, so m ẍ + k x = 0, or ẍ + ω_n² x = 0 with ω_n² = k/m.
  3. Try x = A cos ω_n t + B sin ω_n t: ẍ = −ω_n² x, so it satisfies the equation for any A and B.
  4. Initial conditions x(0) = x₀ and ẋ(0) = v₀ give A = x₀ and B = v₀/ω_n.
  5. Amplitude form: x = X sin(ω_n t + φ) with X = √(x₀² + (v₀/ω_n)²) and tan φ = x₀ ω_n / v₀.
  6. Period and frequency: the motion repeats when ω_n T = 2π, so T = 2π √(m/k) and f_n = 1/T = (1/2π) √(k/m).
  7. Vertical spring: at rest m g = k δ_st, so k/m = g/δ_st and f_n = (1/2π) √(g/δ_st).
  8. Energy (Rayleigh): with x = X sin ω_n t, the maximum strain energy ½ k X² equals the maximum kinetic energy ½ m (ω_n X)², giving again ω_n² = k/m.
  9. Springs in parallel share the displacement: k = k₁ + k₂. Springs in series share the force: 1/k = 1/k₁ + 1/k₂.
  10. Member stiffness from deflection formulas of strength of materials: cantilever with tip load k = 3EI/L³; simply supported beam with central load k = 48EI/L³.
Formulas, symbols and SI units
  • Equation of motion: m ẍ + k x = 0 (m in kg, k in N/m, x in m)
  • ω_n = √(k/m) (rad/s); f_n = ω_n / 2π (Hz); T = 1/f_n = 2π √(m/k) (s)
  • Static deflection form: f_n = (1/2π) √(g/δ_st), δ_st in m, g = 9.81 m/s²
  • x(t) = x₀ cos ω_n t + (v₀/ω_n) sin ω_n t; amplitude X = √(x₀² + (v₀/ω_n)²)
  • Peak velocity ω_n X (m/s); peak acceleration ω_n² X (m/s²)
  • Parallel springs k = k₁ + k₂; series springs 1/k = 1/k₁ + 1/k₂
  • Cantilever k = 3EI/L³; simply supported beam (centre) k = 48EI/L³ (E in N/m², I in m⁴, L in m)
Assumptions and limits
  • Linear elastic spring: force proportional to displacement, so large deflections, cracking or yielding are outside the model.
  • The mass is lumped at one point and the spring (column, beam, pads) is treated as massless; when member mass is significant, an equivalent lumped mass or Rayleigh's method is needed.
  • Only one direction of motion is considered; real structures have many modes, and the SDOF model represents one of them (usually the first).
  • Damping is ignored here, so the motion never dies out; lesson 10.2 adds damping. For natural frequency, light damping makes almost no difference.
  • Foundation flexibility is ignored unless included as an extra spring in series.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • No design code governs this lesson; free vibration of a single-degree system is a principle of mechanics. Design periods, mass and stiffness assumptions for buildings and elevated tanks under earthquakes, comfort limits for footbridges and frequency criteria for machine foundations are taken up in the earthquake engineering, bridge engineering and foundation engineering subjects.

Worked examples

Example 1 (site style)

Problem. An elevated water tank is idealised as a single mass on a cantilever RCC column 12 m high and 1.0 m in diameter, fixed at the base. Take E = 25 000 N/mm² for the concrete. The tank weighs 15 t empty and 50 t full. Find the natural period of lateral vibration for both cases, neglecting the column's own mass.

  1. I = π d⁴ / 64 = π × 1.0⁴ / 64 = 0.04909 m⁴; E = 25 × 10⁹ N/m².
  2. Lateral stiffness of the cantilever: k = 3EI/L³ = 3 × 25 × 10⁹ × 0.04909 / 12³ = 2.1305 × 10⁶ N/m.
  3. Full (m = 50 000 kg): ω_n = √(2.1305 × 10⁶ / 50 000) = √42.61 = 6.528 rad/s; f_n = 1.039 Hz; T = 0.963 s.
  4. Empty (m = 15 000 kg): ω_n = √142.04 = 11.918 rad/s; f_n = 1.897 Hz; T = 0.527 s.
  5. Filling the tank more than triples the mass and nearly doubles the period, which is why tank seismic checks are made for both the full and the empty condition.

Answer. Full: T = 0.96 s (f = 1.04 Hz); empty: T = 0.53 s (f = 1.90 Hz)

Example 2 (exam style)

Problem. A pump set of mass 800 kg stands on spring mounts with total vertical stiffness 200 kN/m. Find the static deflection and the natural frequency. If the set is pushed down 10 mm and released with a downward velocity of 0.2 m/s, find the amplitude of the free vibration.

  1. Static deflection: δ_st = m g / k = 800 × 9.81 / 200 000 = 0.03924 m = 39.2 mm.
  2. ω_n = √(200 000 / 800) = √250 = 15.811 rad/s; f_n = 15.811 / 2π = 2.516 Hz.
  3. Check with the static-deflection form: (1/2π) √(9.81 / 0.03924) = (1/2π) √250 = 2.516 Hz.
  4. Amplitude: X = √(0.010² + (0.2 / 15.811)²) = √(1.0 × 10⁻⁴ + 1.6 × 10⁻⁴) = 0.01612 m.
  5. The amplitude 16.1 mm is larger than the 10 mm push, because the starting velocity adds kinetic energy.

Answer. δ_st = 39.2 mm; f_n = 2.52 Hz; X = 16.1 mm

Example 3 (site style)

Problem. A 500 kg pump is mounted at mid-span of a 4 m simply supported steel beam with EI = 1.0 × 10⁷ N·m², on rubber pads of total stiffness 2.5 × 10⁶ N/m. Neglecting the beam's mass, find the natural frequency with the pads and with the pump bolted directly to the beam.

  1. Beam stiffness at mid-span: k_b = 48EI/L³ = 48 × 1.0 × 10⁷ / 4³ = 7.5 × 10⁶ N/m.
  2. Pads and beam carry the same force, so they act in series: 1/k = 1/(7.5 × 10⁶) + 1/(2.5 × 10⁶), k = 1.875 × 10⁶ N/m.
  3. With pads: ω_n = √(1.875 × 10⁶ / 500) = √3750 = 61.24 rad/s; f_n = 9.75 Hz.
  4. Bolted direct: ω_n = √(7.5 × 10⁶ / 500) = √15 000 = 122.47 rad/s; f_n = 19.49 Hz.
  5. The soft pads halve the natural frequency; lesson 10.3 shows why moving the natural frequency well below the running speed isolates the vibration.

Answer. With pads 9.75 Hz; bolted direct 19.5 Hz

Step-by-step procedure

  1. Decide the direction of motion and the mass that moves (include contents, fixed equipment and a share of slab or beam mass if needed).
  2. Find the stiffness in that direction from a deflection formula, a load test or a spring rating; combine springs in series or parallel.
  3. Compute ω_n = √(k/m), then f_n and T; for vertical mounts check with f_n = (1/2π)√(g/δ_st).
  4. If the motion is needed, use x₀ and v₀ to find the amplitude X and phase φ.
  5. Check the assumptions: linear stiffness, small motion, member mass small compared with the lumped mass.

Site notes

  • The natural frequency of a footbridge, a floor or a tank staging can be measured on site with a phone-grade accelerometer: a light tap or a dropped sandbag starts free vibration, and counting cycles per second gives f_n.
  • Adding mass (a new water tank, heavy finishes, stored material) lowers f_n; adding stiffness (bracing, deeper beams) raises it. Check both before changing the use of a structure.
  • Spring mounts for pumps and generators are chosen by static deflection: a mount that compresses 25 mm under the machine gives f_n of about 3.2 Hz, whatever the machine's mass.
  • A loose or cracked support reduces stiffness, so a drop in measured natural frequency over time is an early sign of damage.
Common mistakes
  • Using weight in newtons in place of mass in kilograms in ω_n = √(k/m).
  • Mixing rad/s and Hz: ω_n is in rad/s, f_n = ω_n / 2π is in Hz.
  • Adding stiffnesses of springs that are in series (they share force, not displacement).
  • Using the static deflection formula f_n = (1/2π)√(g/δ_st) for lateral (horizontal) vibration, where gravity does not set the deflection.
  • Forgetting that a tank, silo or hopper has different natural periods when full and when empty.
Quick check

Vertical mounts: f_n in Hz is close to 15.8 / √δ_st with δ_st in mm (10 mm gives about 5 Hz, 25 mm about 3.2 Hz); valid for linear springs only.

Summary

  • m ẍ + k x = 0; ω_n = √(k/m); T = 2π √(m/k).
  • Vertical systems: f_n = (1/2π)√(g/δ_st).
  • Amplitude X = √(x₀² + (v₀/ω_n)²); peak acceleration ω_n² X.
  • Parallel k₁ + k₂; series 1/k = 1/k₁ + 1/k₂; cantilever 3EI/L³; beam centre 48EI/L³.

Practice questions

Tap a question to see the answer.

1A 2000 kg mass is supported on a spring of stiffness 800 kN/m. Find ω_n, f_n and T.

ω_n = √(800 000 / 2000) = 20 rad/s; f_n = 3.183 Hz; T = 0.314 s.

2A machine deflects its mounts by 5 mm under its own weight. Find its vertical natural frequency.

f_n = (1/2π) √(9.81 / 0.005) = 7.05 Hz.

3Two springs of 30 kN/m and 60 kN/m are connected first in series and then in parallel. Find the equivalent stiffness each way.

Series: 1/k = 1/30 + 1/60, k = 20 kN/m. Parallel: k = 90 kN/m.

4A 4 m cantilever post with EI = 5 × 10⁶ N·m² carries a 2000 kg sign panel at its top. Find the lateral natural period, neglecting the post's mass.

k = 3EI/L³ = 234 375 N/m; ω_n = 10.83 rad/s; T = 0.580 s.

5By what factor does the natural period change if the mass of an SDOF system is doubled with the same stiffness?

T is proportional to √m, so it increases by √2 = 1.414.

6An SDOF system with ω_n = 10 rad/s is displaced 20 mm and released from rest. Find the amplitude, the peak velocity and the peak acceleration.

X = 20 mm; peak velocity ω_n X = 0.2 m/s; peak acceleration ω_n² X = 2 m/s².

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
  • R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
  • J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
  • S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.