Indiacon CivilSubscribe

Textbook › Fluid Mechanics › Chapter 2 › Lesson 2.2

2.2 Hydrostatic forces on surfaces

Fluid Mechanics Chapter 2: Fluid statics Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Derive the hydrostatic force on one side of a plane surface, F = ρ g h_c A, and state the SI units of each symbol.
  • Locate the centre of pressure on an inclined or vertical plane, using y_cp = y_c + I_G / (A y_c) along the plane, or the equivalent depth form h_cp = h_c + I_G sin²θ / (A h_c).
  • Resolve the force on a curved surface into a horizontal component equal to the force on the vertical projection and a vertical component equal to the weight of the liquid vertically above (or displaced by) the surface.
  • Compute both a vertical rectangular gate and a quarter-circular cylindrical gate with the civil conventions ρ = 1000 kg/m³ and g = 9.81 m/s², and say when atmospheric pressure cancels.

Theory

The pressure in a static liquid grows with depth, so a wall, a sluice gate, a tank end or a curved tainter gate is not pushed by a single uniform pressure. The resultant force on one side of the surface, and the point through which that force acts, are what the designer needs in order to size the skin, the hinges and the lifting gear. This lesson starts from the hydrostatic law of Lesson 2.1 and finds that force and that point, first for a plane surface and then for a curved one. Buoyancy, which is the vertical hydrostatic force on a closed body, is Lesson 2.3.

On one side of a plane surface of area A, each element dA at depth h carries a force dF = p dA = (p0 + ρ g h) dA. If the other side of the gate is open to the same atmospheric pressure p0, or if gauge pressures are used from the start, the p0 terms on the two sides cancel and only the liquid gauge pressure ρ g h remains. The resultant liquid force is then F = ∫ ρ g h dA = ρ g h_c A, where h_c is the depth of the centroid of the area. The force is not “ρ g times the average depth times A” as a separate idea: the average depth, for this first moment, is exactly the centroidal depth. The direction of F is perpendicular to the plane, because a static pressure acts normal to a surface (Pascal’s law). The line of action does not, in general, pass through the centroid. Pressure is larger on the deeper elements, so the centre of pressure lies deeper than the centroid. Measuring y along the plane from the line where the plane meets the free surface, a moment balance gives y_cp = y_c + I_G / (A y_c), where I_G is the second moment of the area about a centroidal axis parallel to that surface intersection. The corresponding depth is h_cp = y_cp sin θ = h_c + I_G sin²θ / (A h_c), where θ is the angle of the plane to the horizontal. For a vertical plane, θ = 90° and y and h coincide, so h_cp = h_c + I_G / (A h_c). For a rectangle of width b and height a in the depth direction, I_G = b a³ / 12 about the horizontal centroidal axis.

Hydrostatic forces on surfacesFcentroidcentre of pressurevertical plane: F = ρgh_c AF_HF_Vcurved: F_H, F_Vh_cp = h_c + I_G sin^2 θ / (A h_c)Along the plane: y_cp = y_c + I_G / (A y_c)Indiacon original, not to scale
Figure 2.2: A vertical rectangular gate with the hydrostatic force at the centre of pressure, and a quarter-circular curved gate resolved into F_H and F_V. Indiacon original, not to scale.

A curved surface is handled by components, not by a single normal that changes direction over the surface. The horizontal component F_H is equal to the hydrostatic force on the vertical projection of the surface, and it acts through the centre of pressure of that projected plane area. The vertical component F_V is equal to the weight of the liquid that lies vertically above the surface — or, if the liquid is on the underside, the weight of the liquid that the surface displaces, acting upward. Both statements are just the equilibrium of a free body of liquid bounded by the curved surface and by vertical and horizontal cutting planes. The resultant is F = √(F_H² + F_V²), at an angle tan⁻¹(F_V / F_H) to the horizontal, and it must pass through the intersection of the two component lines of action. For a quarter-circular cylindrical gate of radius R and width b, with the free surface at the top of the quarter-circle and the water occupying the quarter on the concave side, the vertical projection is a rectangle R by b, so F_H = ρ g (R/2) (R b), and F_V is the weight of the quarter-cylinder of water, ρ g (π R² / 4) b, acting downward through the centroid of the quarter-circle, which is 4R / (3π) from each straight radius. The centre of pressure of the vertical projection, whose top is at the free surface, is at a depth 2R/3.

The civil conventions of Lessons 1.1 and 2.1 are used in the examples: ρ = 1000 kg/m³ and g = 9.81 m/s², unless a problem states another value. Atmospheric pressure is the official standard atmosphere 101.325 kPa only when an absolute pressure is being discussed; for a gate with the atmosphere on the dry face, that atmosphere cancels and does not appear in F. If the downstream face is submerged, or is a closed chamber at some other pressure, that pressure must be included, as a uniform addition, and it does shift the centre of pressure toward the centroid. The formulae assume a static liquid of constant density and a rigid surface. They do not include wave slam, flowing-water dynamic pressure, or the self-weight of the gate, which are added separately in a mechanical design.

Derivation

  1. From Lesson 2.1, the gauge pressure at depth h is ρ g h. On a plane element, dF = ρ g h dA. Integrating, F = ρ g ∫ h dA. By definition of the centroid, ∫ h dA = h_c A, so F = ρ g h_c A. If both sides of the surface are exposed to the same atmospheric pressure, the atmospheric contributions cancel and this F is the net force.
  2. Let y be the distance along the plane from the intersection of the plane with the free surface, and let θ be the inclination of the plane to the horizontal, so that h = y sin θ. Then F = ρ g sin θ ∫ y dA = ρ g sin θ (y_c A). The moment of the distributed force about the intersection axis is ρ g sin θ ∫ y² dA = ρ g sin θ I_O, with I_O = I_G + A y_c². Dividing the moment by the force gives y_cp = I_O / (A y_c) = y_c + I_G / (A y_c). Multiplying by sin θ gives the depth form h_cp = h_c + I_G sin²θ / (A h_c). For a vertical plane, sin θ = 1 and the two statements coincide.
  3. For a rectangle of width b and side a measured in the y-direction, I_G = b a³ / 12 about the centroidal axis parallel to the width.
  4. Horizontal component on a curved surface: a vertical cutting plane through the edges of the surface has area A_v and centroidal depth h_c,v, so F_H = ρ g h_c,v A_v, acting at the centre of pressure of A_v. Vertical component: the free body of liquid above the surface is in equilibrium, so F_V equals the weight of that liquid, acting through its centre of mass. For a quarter-circle of radius R and width b with the free surface at the top, A_v = R b, h_c,v = R/2, F_H = ρ g R² b / 2, and F_V = ρ g (π R² / 4) b. The centre of pressure of the vertical rectangle with its top at the free surface is at depth 2R/3. The centroid of a quarter-circular area is 4R / (3π) from each straight radius.
Formulas, symbols and SI units
  • Plane surface, one side, atmosphere cancelling: F = ρ g h_c A (N), with h_c the centroidal depth (m) and A the area (m²)
  • Along the plane, from the free-surface intersection: y_cp = y_c + I_G / (A y_c)
  • Depth of the centre of pressure: h_cp = h_c + I_G sin²θ / (A h_c), θ = angle of the plane to the horizontal
  • Vertical plane: h_cp = h_c + I_G / (A h_c)
  • Rectangle, width b, depth-side a: I_G = b a³ / 12 (m⁴)
  • Curved surface: F_H = force on the vertical projection; F_V = weight of liquid vertically above (down) or displaced (up); F = √(F_H² + F_V²)
  • Quarter-circular cylinder, free surface at the top, radius R, width b: F_H = ρ g R² b / 2; F_V = ρ g (π R² / 4) b; projected centre of pressure at depth 2R/3; quarter-circle centroid at 4R / (3π) from each radius
  • Civil working values in the examples: ρ = 1000 kg/m³, g = 9.81 m/s²
Assumptions and limits
  • F = ρ g h_c A is the net force from the liquid when the atmospheric pressure on the two faces is the same and has been cancelled. A different pressure on the downstream face must be added as a uniform load and will move the centre of pressure.
  • The liquid is static and of constant density. The civil conventions ρ = 1000 kg/m³ and g = 9.81 m/s² are those of Lessons 1.1 and 2.1, unless a problem states other values.
  • y is measured along the plane from the line of intersection with the free surface. If that intersection is above a closed pressurised surface, an equivalent free surface (the level where the gauge pressure would be zero) is used.
  • I_G is about the centroidal axis parallel to the surface intersection. A second moment about a different axis is not I_G.
  • The quarter-circle formulae above are for water on the concave side with the free surface at the top of the quarter-circle. A different geometry (water on the convex side, or a partly filled gate) changes the free body and must be redrawn.
  • The self-weight of the gate, hinges, friction and flowing-water dynamic forces are not included. This lesson is the hydrostatic part only.
  • This lesson does not size a member, does not use a code partial factor, and does not copy a textbook figure.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • The force and centre-of-pressure formulae are continuum mechanics, not an Indian Standard clause. Lessons 2.1’s official standard atmosphere (ISO 2533 p0 = 101 325 Pa) is named only to recall that, when it acts on both faces of a gate, it cancels from the net force.
  • BIPM SI Brochure (9th edition, 2019) — SI units (newton, pascal, metre).
  • Background textbooks, not ranked: F. M. White, Fluid Mechanics; B. R. Munson, D. F. Young, T. H. Okiishi, W. W. Huebsch, Fundamentals of Fluid Mechanics.

Worked examples

Example 1 (illustrative): vertical rectangular gate

Problem. A vertical rectangular gate is 1.20 m wide and 1.80 m high. Its top edge is 2.00 m below the free surface of water. The downstream face is open to the atmosphere. Taking ρ = 1000 kg/m³ and g = 9.81 m/s², find the net hydrostatic force on the gate and the depth of the centre of pressure.

  1. Area A = 1.20 × 1.80 = 2.16 m². The centroid is halfway down the gate, so h_c = 2.00 + 1.80 / 2 = 2.90 m.
  2. F = ρ g h_c A = 1000 × 9.81 × 2.90 × 2.16 = 61 449.84 N = 61.450 kN. Atmospheric pressure acts on both faces and cancels, so this is the net force, acting horizontally.
  3. I_G = b a³ / 12 = 1.20 × (1.80)³ / 12 = 1.20 × 5.832 / 12 = 0.5832 m⁴.
  4. The gate is vertical, so h_cp = h_c + I_G / (A h_c) = 2.90 + 0.5832 / (2.16 × 2.90) = 2.90 + 0.5832 / 6.264 = 2.90 + 0.09310 = 2.993 m, or 93 mm below the centroid.
  5. The same offset is I_G / (A h_c) = 0.09310 m. The force should be taken at 2.993 m below the free surface, not at the centroid, when the moment on the hinges is computed.

Answer. F = 61.450 kN; h_cp = 2.993 m below the free surface (93 mm below the centroid).

Example 2 (illustrative): quarter-circular cylindrical sluice

Problem. A quarter-circular cylindrical gate of radius 1.50 m and width 2.00 m is set in a vertical wall. The free surface of the water is at the top of the quarter-circle, and the water occupies the quarter on the concave side, so that the upper radius lies horizontally in the free surface and the other radius runs vertically down the wall, with the curved gate below the water. Taking ρ = 1000 kg/m³ and g = 9.81 m/s², find the horizontal and vertical components of the hydrostatic force, the resultant, the angle of the resultant to the horizontal, the depth of the line of action of F_H, and the position of the line of action of F_V.

  1. Vertical projection is a rectangle 1.50 m by 2.00 m, with its top at the free surface, so h_c,v = 1.50 / 2 = 0.75 m and A_v = 1.50 × 2.00 = 3.00 m².
  2. F_H = ρ g h_c,v A_v = 1000 × 9.81 × 0.75 × 3.00 = 22 072.5 N = 22.073 kN, or equivalently F_H = ρ g R² b / 2 = 1000 × 9.81 × (1.50)² × 2.00 / 2 = 22 072.5 N. This force acts at the centre of pressure of the projected rectangle. With the top at the free surface, that depth is 2R/3 = 1.00 m (check: I_G,v = 2.00 × (1.50)³ / 12 = 0.5625 m⁴, offset = 0.5625 / (3.00 × 0.75) = 0.25 m, so h_cp,v = 0.75 + 0.25 = 1.00 m).
  3. F_V is the weight of the quarter-cylinder of water, acting downward: volume = (π R² / 4) b = (π × 2.25 / 4) × 2.00 = 3.534292 m³; F_V = 1000 × 9.81 × 3.534292 = 34 671.4 N = 34.671 kN. The line of action passes through the centroid of the quarter-circle, at 4R / (3π) = 4 × 1.50 / (3π) = 0.637 m from the vertical radius and from the horizontal radius.
  4. Resultant F = √(F_H² + F_V²) = √(22 072.5² + 34 671.4²) = 41 101.1 N = 41.101 kN. The angle to the horizontal is tan⁻¹(F_V / F_H) = tan⁻¹(34 671.4 / 22 072.5) = 57.52°. The resultant passes through the intersection of a horizontal line 1.00 m below the free surface and a vertical line 0.637 m from the vertical wall radius.

Answer. F_H = 22.073 kN at 1.00 m depth; F_V = 34.671 kN downward, 0.637 m from each radius; F = 41.101 kN at 57.52° to the horizontal.

Step-by-step procedure

  1. Sketch the surface, the free surface, and the dry (or downstream) face. Decide whether atmospheric pressure cancels.
  2. For a plane surface, compute the area A and the centroidal depth h_c, then F = ρ g h_c A. Use ρ = 1000 kg/m³ and g = 9.81 m/s² unless the problem states other values.
  3. Compute I_G about the correct centroidal axis. If the plane is inclined, decide whether to work in y along the plane (y_cp = y_c + I_G / (A y_c)) or in depth (h_cp = h_c + I_G sin²θ / (A h_c)). For a vertical plane the two are the same.
  4. For a curved surface, draw the vertical projection and the volume of liquid above (or displaced by) the surface. Compute F_H from the projected plane and F_V from the weight of that volume. Place F_H at the projected centre of pressure and F_V through the centroid of the volume. Combine to a resultant only if that resultant is needed.
  5. If the downstream face is submerged, compute a second force on that face and take the vector difference, or work throughout in gauge pressure relative to the downstream free surface.
  6. When reporting a hinge moment, take the force at the centre of pressure, not at the centroid. The offset I_G / (A h_c) is small for a deep, short gate and large for a shallow, tall one; check that the sign is downward.
  7. Do not include the self-weight of the gate in the hydrostatic force; add it separately in the mechanical equilibrium of the gate.

Site notes

  • A sluice that is “just under water” can have a centre of pressure a noticeable way below mid-height. Taking the force at mid-height then underestimates the moment on the bottom hinge or the invert seal.
  • If the downstream side is not freely vented to the atmosphere — a drowned outlet, a closed chamber, a blocked vent — the cancellation of atmosphere no longer holds in the way the dry-face calculation assumed. Check the downstream condition before using F = ρ g h_c A as the net force.
  • A curved tainter gate has a large vertical component. The hoisting gear has to lift against F_V as well as against the gate’s self-weight; the horizontal component is carried to the trunnions.
  • Silt on the invert changes both the density and the effective area. The clean-water calculation of this lesson is a starting value, not a silted-gate value.
  • Stop-logs and stoplog slots: the force on each log is computed as a separate rectangle at its own depth. Adding the log forces is correct; using a single centroid for the whole opening is correct only if the logs really form one plane surface.
  • Wave action and a flowing approach are not hydrostatic. For a spillway gate in a flood, this lesson is the static part only.
Common mistakes
  • Taking the force at the centroid, or writing F = ρ g h_max A, as if the pressure were the invert pressure over the whole gate.
  • Using I about the top edge, or about a vertical axis, in the centre-of-pressure formula, instead of I_G about the horizontal centroidal axis.
  • Forgetting sin²θ in the depth form on an inclined plane, or inserting an extra sin θ into y_cp = y_c + I_G / (A y_c), which already uses distances along the plane.
  • On a curved surface, taking F as ρ g h_c A of the curved area itself, instead of resolving into F_H and F_V.
  • Giving F_V the wrong sense (up instead of down, or the reverse) because the free body was not drawn.
  • Adding atmospheric pressure to F when the downstream face is open to the atmosphere, so that the atmosphere has already cancelled.
  • Mixing ρ = 1000 kg/m³ with g = 9.81 m/s² in one part of the sum and γ = 10 kN/m³ in another, without a stated reason.
Quick check

Plane, atmosphere cancelling: F = ρg h_c A, at h_cp = h_c + I_G sin²θ / (A h_c); along the plane, y_cp = y_c + I_G / (A y_c). Vertical rectangle: I_G = b a³/12. Curved: F_H = force on the vertical projection; F_V = weight of liquid above (down) or displaced (up). Civil water: ρ = 1000 kg/m³, g = 9.81 m/s².

Summary

  • The net hydrostatic force on one side of a plane surface, when atmospheric pressure cancels, is F = ρ g h_c A, acting normal to the plane at the centre of pressure, which is deeper than the centroid.
  • Along the plane, y_cp = y_c + I_G / (A y_c). In depth, h_cp = h_c + I_G sin²θ / (A h_c). For a vertical plane the two statements coincide.
  • A curved surface is resolved into a horizontal force equal to the force on the vertical projection and a vertical force equal to the weight of the liquid above or displaced by the surface.
  • For a quarter-circular cylindrical gate with the free surface at the top, F_H = ρ g R² b / 2 at depth 2R/3, and F_V = ρ g (π R² / 4) b through the quarter-circle centroid at 4R / (3π) from each radius.
  • The civil working values in the examples are ρ = 1000 kg/m³ and g = 9.81 m/s². The self-weight of the gate and any flowing-water forces are not included.

Practice questions

Tap a question to see the answer.

1A vertical rectangular gate has A = 3.00 m² and h_c = 2.00 m. With ρ = 1000 kg/m³ and g = 9.81 m/s², what is F?

F = 1000 × 9.81 × 2.00 × 3.00 = 58.86 kN.

2For the same gate, I_G = 0.90 m⁴. What is h_cp?

h_cp = 2.00 + 0.90 / (3.00 × 2.00) = 2.00 + 0.15 = 2.15 m.

3A rectangle is 0.80 m wide and 1.20 m in the depth direction. What is I_G about the horizontal centroidal axis?

I_G = 0.80 × (1.20)³ / 12 = 0.80 × 1.728 / 12 = 0.1152 m⁴.

4Why does the centre of pressure lie below the centroid on a plane surface that is not horizontal?

Because the pressure increases with depth, so the deeper elements carry a larger force and the resultant acts below the centroid. (On a horizontal surface the pressure is uniform and the two points coincide.)

5A quarter-circular gate has R = 1.00 m and b = 1.00 m, with the free surface at the top. With ρ = 1000 kg/m³ and g = 9.81 m/s², what is F_H?

F_H = 1000 × 9.81 × (1.00)² × 1.00 / 2 = 4 905 N = 4.905 kN, acting at depth 2R/3 = 0.667 m.

6In that last geometry, at what distance from each radius does F_V act?

At the quarter-circle centroid, 4R / (3π) = 4 / (3π) = 0.424 m from each straight radius.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • F. M. White, Fluid Mechanics, McGraw Hill, 8th edition, 2016.
  • B. R. Munson, D. F. Young, T. H. Okiishi, W. W. Huebsch, Fundamentals of Fluid Mechanics, Wiley, 8th edition, 2016.
  • ISO 2533, Standard Atmosphere, named only for the cancellation of atmospheric pressure on a gate open to the air. BIPM, The International System of Units (SI Brochure), 9th edition, 2019.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.