10.3 Forced vibration and resonance
After this lesson you should be able to:
- Write the equation of motion of a damped single-degree system under a harmonic force, m ẍ + c ẋ + k x = F₀ sin ωt, and derive its steady-state amplitude and phase.
- Use the frequency ratio r = ω/ω_n and the dynamic magnification factor DMF = 1/√((1 − r²)² + (2ζr)²) to judge how close a system is to resonance.
- Use the force transmissibility TR to design vibration isolation for machines, and recognise why isolation works only when r > √2.
Theory
When a repeating force acts on a structure, the structure ends up vibrating at the frequency of the force, not at its own natural frequency. Examples are the unbalance of a rotating pump, fan or motor, the footfall of people walking or jumping on a floor or footbridge, the regular passing of axles over a joint, and the shedding of vortices from a chimney in wind. The simplest model is a harmonic force F₀ sin ωt acting on the damped single-degree system of lesson 10.2.
The full response has two parts. The transient part is the damped free vibration started at the beginning; it dies out at the rate set by ζ. What remains is the steady state, a sine wave at the forcing frequency ω whose amplitude X is the static deflection F₀/k multiplied by the dynamic magnification factor (DMF). The DMF depends only on the frequency ratio r = ω/ω_n and the damping ratio ζ. Well below resonance (r much less than 1) the DMF is close to 1: the structure follows the force almost statically. Well above resonance (r much greater than 1) it falls towards 1/r²: the mass is too sluggish to follow.
At resonance, r = 1, the DMF equals 1/(2ζ). For a footbridge with ζ = 1 % that is 50: a force that would deflect the deck by a fraction of a millimetre statically can make it move by several millimetres, enough to be felt and disliked. The response also lags behind the force by a phase angle φ, which is near 0° below resonance, exactly 90° at resonance and near 180° well above it. Light damping does little to the natural frequency but is the only thing that limits the response at resonance.
Machine foundations add a second question: how much of the machine's force is passed into the supporting floor or soil? The transmissibility TR, the ratio of the transmitted force amplitude to F₀, is greater than 1 for r < √2 and less than 1 for r > √2. Isolation therefore means making the mounts soft enough that the natural frequency is well below the running speed. A rotating unbalance m_e e produces a force F₀ = m_e e ω², so the force grows with the square of the speed, and the machine passes through resonance briefly each time it starts and stops.
Derivation
- Equation of motion with a harmonic force: m ẍ + c ẋ + k x = F₀ sin ωt.
- Steady-state trial: x_p = X sin(ωt − φ). Substitute and separate the sin ωt and cos ωt terms: X (k − m ω²) = F₀ cos φ and X c ω = F₀ sin φ.
- Square and add: X = F₀ / √((k − m ω²)² + (c ω)²).
- Divide top and bottom by k, using m/k = 1/ω_n² and c/k = 2ζ/ω_n: X = (F₀/k) / √((1 − r²)² + (2ζ r)²), with r = ω/ω_n.
- So DMF = X / (F₀/k) = 1 / √((1 − r²)² + (2ζ r)²), and tan φ = 2ζ r / (1 − r²).
- At r = 1: DMF = 1/(2ζ) and φ = 90°. Setting d(DMF)/dr = 0 gives the true peak at r = √(1 − 2ζ²) with DMF_max = 1 / (2ζ √(1 − ζ²)).
- Force transmitted to the base = spring force + damper force = k x + c ẋ, with amplitude X √(k² + (c ω)²); dividing by F₀ gives TR = √(1 + (2ζ r)²) / √((1 − r²)² + (2ζ r)²).
- TR = 1 when (1 − r²)² = 1, that is r = √2, for any ζ; above r = √2, TR < 1 and increasing ζ makes TR slightly larger.
- Undamped isolation design: TR = 1/(r² − 1), so for a target TR the required r² = 1 + 1/TR.
- Rotating unbalance: an eccentric mass m_e at radius e spinning at ω gives F₀ = m_e e ω².
m ẍ + c ẋ + k x = F₀ sin ωt (F₀ in N, ω in rad/s)Frequency ratio r = ω / ω_n (dimensionless)Steady-state amplitude X = (F₀/k) × DMF (m)DMF = 1 / √((1 − r²)² + (2ζ r)²); at r = 1 DMF = 1/(2ζ)Phase tan φ = 2ζ r / (1 − r²); φ = 90° at resonancePeak DMF_max = 1 / (2ζ √(1 − ζ²)) at r = √(1 − 2ζ²)TR = √(1 + (2ζ r)²) / √((1 − r²)² + (2ζ r)²); TR < 1 only for r > √2Undamped isolation: TR = 1/(r² − 1); rotating unbalance F₀ = m_e e ω² (m_e e in kg·m)
- Linear SDOF system with viscous damping; the result describes one mode near its own natural frequency.
- The force is harmonic with constant amplitude and frequency; real footfall, traffic and wind forces contain several harmonics and vary in time.
- Steady state only: the transient part has died out, which takes several cycles at light damping.
- The base is rigid in the transmissibility formula; a flexible floor or soil adds another spring and changes the result.
- Damping ratios and forces in the examples are illustrative values, not design values.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; forced vibration and resonance of a single-degree system are principles of mechanics. Frequency and amplitude criteria for machine foundations, comfort checks for footbridges and floors, wind-induced oscillation of chimneys and earthquake response are taken up in the foundation engineering, bridge engineering, structural analysis and earthquake engineering subjects.
Worked examples
Problem. The 800 kg pump set of lessons 10.1 and 10.2 (k = 200 kN/m, ζ = 0.0791) runs at 1440 rev/min with a rotating unbalance of 0.1 kg·m. Find the steady-state amplitude, the phase lag and the force passed to the floor. Then find the amplitude while the pump passes through resonance on start-up, taking the steady-state value at ω = ω_n as an upper estimate.
- ω = 2π × 1440 / 60 = 150.80 rad/s; ω_n = 15.811 rad/s; r = 9.537.
- F₀ = m_e e ω² = 0.1 × 150.80² = 2274 N.
- DMF = 1 / √((1 − 9.537²)² + (2 × 0.0791 × 9.537)²) = 0.01111; X = (2274 / 200 000) × 0.01111 = 0.126 mm.
- tan φ = 2ζr / (1 − r²) is small and negative, so φ = 179.0°: the mass moves opposite to the force.
- TR = √(1 + 1.508²) × 0.01111 = 0.0201, so the floor feels 0.0201 × 2274 = 45.7 N, about 2 % of the unbalance force.
- At resonance on start-up: F₀ = 0.1 × 15.811² = 25 N, DMF = 1 / (2 × 0.0791) = 6.32, X = (25 / 200 000) × 6.32 = 0.79 mm.
Answer. Running: X = 0.13 mm, φ = 179°, 45.7 N to the floor; start-up resonance about 0.79 mm
Problem. The footbridge of lesson 10.2 Example 1 (f_n = 2.0 Hz, ζ = 0.01371) has a modal mass of 20 000 kg. A shaker applies a harmonic vertical force of 280 N. Find the steady-state amplitude and acceleration at 2.0 Hz (resonance), and the amplitude at 1.6 Hz.
- k = m ω_n² = 20 000 × (2π × 2.0)² = 3.158 × 10⁶ N/m; static deflection F₀/k = 0.0887 mm.
- At resonance DMF = 1 / (2 × 0.01371) = 36.5, so X = 0.0887 × 36.5 = 3.23 mm.
- Acceleration amplitude = ω² X = (4π)² × 0.003233 = 0.511 m/s².
- At 1.6 Hz, r = 0.8: DMF = 1 / √((1 − 0.64)² + (2 × 0.01371 × 0.8)²) = 2.77, so X = 0.0887 × 2.77 = 0.246 mm.
- Moving 20 % off resonance cuts the response by a factor of about 13: this is why footbridges with a natural frequency near normal walking pace are checked and sometimes fitted with tuned mass dampers.
Answer. 3.23 mm and 0.51 m/s² at resonance; 0.25 mm at 1.6 Hz
Problem. A 600 kg pump running at 1500 rev/min is to be mounted on springs so that no more than 10 % of its unbalanced force reaches the floor. Neglecting damping, find the highest allowable natural frequency, the least static deflection of the springs and the largest total spring stiffness. Then check TR if the mounts actually have ζ = 0.05.
- ω = 2π × 1500 / 60 = 157.08 rad/s.
- TR = 1/(r² − 1) ≤ 0.1, so r² ≥ 11 and r ≥ 3.317.
- ω_n ≤ 157.08 / 3.317 = 47.36 rad/s, so f_n ≤ 7.54 Hz.
- δ_st = g / ω_n² ≥ 9.81 / 47.36² = 4.37 mm; k ≤ m ω_n² = 600 × 2243 = 1.346 × 10⁶ N/m.
- With ζ = 0.05 at r = 3.317: TR = √(1 + 0.3317²) / √((1 − 11)² + 0.3317²) = 0.1053, slightly above 0.1, so choose springs a little softer than the limit.
Answer. f_n ≤ 7.54 Hz; δ_st ≥ 4.4 mm; k ≤ 1.35 MN/m; with 5 % damping TR = 0.105
Step-by-step procedure
- Model the system: mass m, stiffness k, damping ratio ζ; find ω_n = √(k/m).
- Identify the forcing: F₀ and ω (for rotating unbalance F₀ = m_e e ω²; for footfall, the frequency of the harmonic of concern).
- Compute r = ω/ω_n, then DMF and X = (F₀/k) DMF, and the phase φ if needed.
- For machine mounts compute TR and the transmitted force; for isolation choose k so that r is comfortably above √2 (usually r of 3 or more).
- Check start-up and shut-down, when the machine passes through r = 1, and check other harmonics of the force.
Site notes
- Avoid resonance by separating frequencies, not by adding strength: stiffen to raise ω_n well above the forcing or soften the mounts to drop it well below.
- Isolated machines pass through resonance on every start and stop; a quick run-up, snubbers or extra damping keep the start-up amplitude in check.
- Flexible pipe connections are needed on spring-mounted pumps; a rigid pipe shorts out the isolation and carries vibration into the building.
- When people complain of a lively floor or footbridge, measure f_n and ζ first (lesson 10.2); the fix depends on whether the problem is resonance or simply low stiffness.
- Comparing a frequency in Hz with an ω_n in rad/s when forming r.
- Using the static deflection F₀/k as the dynamic amplitude near resonance.
- Adding damping to improve isolation above r = √2, where it slightly increases the transmitted force.
- Designing isolators only for the running speed and ignoring the passage through resonance at start-up.
- Forgetting that a rotating unbalance force grows with ω², so F₀ is not constant across speeds.
At resonance the amplitude is the static deflection times 1/(2ζ): 1 % damping magnifies 50 times, 5 % magnifies 10 times. Isolation needs r > √2; r = 3 gives TR of about 0.125 for light damping.
Summary
- Steady state: X = (F₀/k) / √((1 − r²)² + (2ζr)²), r = ω/ω_n.
- Resonance r = 1: DMF = 1/(2ζ), φ = 90°.
- TR < 1 only when r > √2; undamped TR = 1/(r² − 1).
- Rotating unbalance F₀ = m_e e ω²; separate frequencies rather than adding strength.
Practice questions
Tap a question to see the answer.
1An undamped system is forced at half its natural frequency. Find the DMF.
r = 0.5: DMF = 1 / (1 − 0.25) = 1.333.
2A system with ζ = 5 % is forced exactly at its natural frequency. Find the DMF and the phase angle.
DMF = 1 / (2 × 0.05) = 10; φ = 90°.
3An undamped system is forced at twice its natural frequency. Find the DMF and the phase.
DMF = 1 / |1 − 4| = 0.333; φ = 180° (motion opposite to the force).
4Find the transmissibility of an undamped isolator with r = 3.
TR = 1 / (9 − 1) = 0.125.
5A fan has a rotating unbalance of 0.05 kg·m and runs at 1000 rev/min. Find the amplitude of the unbalance force.
ω = 104.72 rad/s; F₀ = 0.05 × 104.72² = 548 N.
6For ζ = 0.1, find the frequency ratio at which the DMF is greatest and its value.
r = √(1 − 2 × 0.01) = 0.990; DMF_max = 1 / (2 × 0.1 × √0.99) = 5.03.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.