10.2 Damped free vibration
After this lesson you should be able to:
- Add viscous damping to the single-degree model, m ẍ + c ẋ + k x = 0, and define the critical damping c_c = 2√(km) and the damping ratio ζ = c/c_c.
- Classify motion as underdamped, critically damped or overdamped, and write the underdamped solution with its damped frequency ω_d = ω_n √(1 − ζ²).
- Measure damping on site from a free-decay record using the logarithmic decrement δ and convert it to ζ.
Theory
Real vibrations die away. Energy is lost to friction in joints and bearings, to micro-cracking and internal friction in concrete and steel, to the soil under a foundation and to purpose-built dampers. The simplest way to model all of this is viscous damping: a force −c ẋ that opposes the velocity, where c is the damping coefficient in N·s/m. It is exact for an oil dashpot and a good average for most structures when the motion is small.
With damping the equation of motion becomes m ẍ + c ẋ + k x = 0. What happens depends on how c compares with a special value, the critical damping c_c = 2√(km) = 2 m ω_n. The ratio ζ = c/c_c, the damping ratio, is the number engineers use. If ζ < 1 (underdamped) the mass oscillates with an amplitude that shrinks by the same ratio every cycle. If ζ = 1 (critically damped) it returns to rest as fast as possible without overshooting. If ζ > 1 (overdamped) it creeps back slowly without oscillating.
Almost every civil structure is lightly underdamped: welded steel footbridges and towers have ζ of around 0.5 to 2 %, reinforced concrete buildings of a few per cent. For such small ζ the damped frequency ω_d = ω_n √(1 − ζ²) is practically equal to ω_n, so damping hardly changes the period. What it does change is how quickly free vibration dies out and, as lesson 10.3 shows, how large the response becomes at resonance.
Damping cannot be calculated reliably from drawings; it is measured. Start a free vibration (a tap, a sandbag drop, a sudden release) and record the peaks. The natural logarithm of the ratio of two successive peaks, the logarithmic decrement δ, is the same for every cycle of a viscously damped system and gives ζ = δ / √(4π² + δ²), close to δ/2π for light damping. Using peaks several cycles apart improves accuracy.
Derivation
- Free-body diagram: spring force −k x and damper force −c ẋ act on the mass, so m ẍ + c ẋ + k x = 0.
- Try x = e^(s t): m s² + c s + k = 0, so s = [−c ± √(c² − 4 m k)] / 2m.
- The roots change type when c² = 4 m k, which defines critical damping c_c = 2√(km) = 2 m ω_n; write ζ = c/c_c, so s = ω_n (−ζ ± √(ζ² − 1)).
- ζ > 1: two real negative roots, motion decays without oscillation (overdamped). ζ = 1: repeated root, x = (A + B t) e^(−ω_n t) (critically damped).
- ζ < 1: complex roots s = −ζ ω_n ± i ω_d with ω_d = ω_n √(1 − ζ²), so x = X e^(−ζ ω_n t) sin(ω_d t + φ) (underdamped).
- Successive peaks are one damped period T_d = 2π/ω_d apart, so x_i / x_(i+1) = e^(ζ ω_n T_d) and δ = ln(x_i / x_(i+1)) = 2π ζ / √(1 − ζ²).
- Solving for ζ: ζ = δ / √(4π² + δ²); for small ζ, ζ ≈ δ / 2π.
- Over n cycles: x₀ / x_n = e^(n δ), so δ = (1/n) ln(x₀ / x_n); the number of cycles for the amplitude to halve is ln 2 / δ.
m ẍ + c ẋ + k x = 0 (c in N·s/m)Critical damping c_c = 2√(km) = 2 m ω_n (N·s/m); damping ratio ζ = c / c_c (dimensionless)Damped frequency ω_d = ω_n √(1 − ζ²) (rad/s); damped period T_d = 2π/ω_d (s)Underdamped response x = X e^(−ζ ω_n t) sin(ω_d t + φ)Log decrement δ = ln(x_i / x_(i+1)) = 2πζ / √(1 − ζ²); over n cycles δ = (1/n) ln(x₀ / x_n)ζ = δ / √(4π² + δ²) ≈ δ / 2π for small dampingTime to decay to a fraction p of the amplitude: t = ln(1/p) / (ζ ω_n)
- Damping is viscous (force proportional to velocity). Friction (Coulomb) damping gives a straight-line, not exponential, decay, and the log decrement is then not constant.
- The structure stays linear and the amplitude is small; damping in real structures grows somewhat with amplitude.
- The record is dominated by one mode; when two frequencies are close the peaks beat and the log decrement varies from cycle to cycle.
- Damping ratios quoted in examples are assumed values for illustration, not design values.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; the damped free vibration of a single-degree system is a principle of mechanics. Damping values to be used in design (for example for earthquake spectra, wind response or footbridge checks) are set in the earthquake engineering, structural analysis and bridge engineering subjects and are not given here.
Worked examples
Problem. After a sandbag is dropped on a steel footbridge, the vertical acceleration record shows a peak of 4.0 units, and the peak five cycles later is 2.6 units. The damped frequency is 2.0 Hz. Find the logarithmic decrement, the damping ratio, the undamped natural frequency and how many cycles it takes for the motion to halve.
- δ = (1/5) ln(4.0 / 2.6) = 0.2 × 0.43078 = 0.08616.
- ζ = δ / √(4π² + δ²) = 0.08616 / √(39.478 + 0.0074) = 0.08616 / 6.2838 = 0.01371, about 1.4 %.
- f_n = f_d / √(1 − ζ²) = 2.0 / √(1 − 0.000188) = 2.0002 Hz, the same as f_d for practical purposes.
- Cycles to halve: ln 2 / δ = 0.69315 / 0.08616 = 8.05 cycles, about 4 s at 2 Hz.
- Light damping like this is why a footbridge near 2 Hz needs a resonance check (lesson 10.3).
Answer. δ = 0.086; ζ = 1.37 %; f_n = 2.00 Hz; about 8 cycles to halve
Problem. The 800 kg pump set of lesson 10.1 (k = 200 kN/m) is fitted with a dashpot of c = 2000 N·s/m. Find c_c, ζ, ω_d, the logarithmic decrement, and the amplitude after 3 full cycles if the starting peak is 10 mm.
- c_c = 2√(km) = 2√(200 000 × 800) = 2 × 12 649 = 25 298 N·s/m.
- ζ = 2000 / 25 298 = 0.07906.
- ω_n = 15.811 rad/s; ω_d = 15.811 × √(1 − 0.00625) = 15.762 rad/s.
- δ = 2π × 0.07906 / √(0.99375) = 0.4983; each peak is e^δ = 1.646 times the next.
- After 3 cycles: 10 × e^(−3 × 0.4983) = 10 × 0.2243 = 2.24 mm.
Answer. c_c = 25.3 kN·s/m; ζ = 0.079; ω_d = 15.76 rad/s; δ = 0.498; 2.24 mm after 3 cycles
Problem. For the full water tank of lesson 10.1 Example 1 (m = 50 000 kg, k = 2.1305 × 10⁶ N/m), assume a damping ratio of 5 % for illustration. Find the damping coefficient, the time and the number of cycles for a free vibration to decay to 10 % of its starting amplitude.
- c = 2ζ√(km) = 2 × 0.05 × √(2.1305 × 10⁶ × 50 000) = 0.1 × 326 382 = 32 638 N·s/m.
- ω_n = 6.528 rad/s, so ζ ω_n = 0.3264 s⁻¹.
- Time: t = ln(1 / 0.1) / (ζ ω_n) = 2.3026 / 0.3264 = 7.05 s.
- T_d = 2π / (6.528 × √(1 − 0.0025)) = 0.9638 s, so the number of cycles is 7.05 / 0.9638 = 7.3.
- Even with 5 % damping the tank sways for about seven cycles; damping limits motion but does not stop it at once.
Answer. c = 32.6 kN·s/m; 7.05 s; about 7.3 cycles
Step-by-step procedure
- Write m ẍ + c ẋ + k x = 0 and compute ω_n = √(k/m) and c_c = 2√(km).
- Find ζ = c/c_c and classify the motion: under-, critically or over-damped.
- For underdamped motion find ω_d = ω_n √(1 − ζ²) and use x = X e^(−ζ ω_n t) sin(ω_d t + φ).
- To measure damping, record free decay, pick peaks n cycles apart, compute δ = (1/n) ln(x₀/x_n) and ζ = δ/√(4π² + δ²).
- Check that the decay is exponential (constant δ); if not, friction damping or several modes are present.
Site notes
- Free-decay tests are cheap: a sandbag drop or a sudden release with a rope gives a decay record from which both f_n and ζ come out of the same few seconds of data.
- Use peaks several cycles apart rather than two neighbours; a 5 % error in reading small peaks becomes a large error in ζ.
- Bolted and clad structures usually show more damping than bare welded frames; damping measured before fit-out may be lower than in service.
- Dampers (viscous, tuned mass, friction) are added where measured damping is too low for the response wanted; their selection belongs to the earthquake and bridge subjects.
- Using log base 10 in place of the natural logarithm in δ.
- Taking δ = 2πζ without the √(1 − ζ²) term when ζ is not small (for example above about 0.2).
- Dividing the log of the ratio over n cycles by n − 1, or not dividing by n at all.
- Treating ζ as a design value from an example; design damping comes from the governing code of the relevant subject.
- Expecting damping to change the natural period noticeably; for light damping it hardly does.
For light damping ζ ≈ δ / 2π, and the amplitude halves in about 0.11 / ζ cycles (1 % damping: about 11 cycles; 5 %: about 2.2 cycles).
Summary
- m ẍ + c ẋ + k x = 0; c_c = 2√(km); ζ = c/c_c.
- ζ < 1 oscillates and decays; ζ = 1 fastest return without overshoot; ζ > 1 creeps back.
- ω_d = ω_n √(1 − ζ²) ≈ ω_n for civil structures.
- δ = ln(x_i/x_(i+1)) = 2πζ/√(1 − ζ²); ζ = δ/√(4π² + δ²).
Practice questions
Tap a question to see the answer.
1Find the critical damping coefficient for a 100 kg mass on a 40 kN/m spring.
c_c = 2√(40 000 × 100) = 4000 N·s/m.
2The system of question 1 has c = 400 N·s/m. Find ζ, ω_n and ω_d.
ζ = 0.1; ω_n = 20 rad/s; ω_d = 20 √0.99 = 19.90 rad/s.
3Two successive peaks of a free-decay record are 10 mm and 8 mm. Find δ and ζ.
δ = ln 1.25 = 0.2231; ζ = 0.2231 / √(4π² + 0.2231²) = 0.0355.
4A structure has ζ = 2 %. Find the log decrement and the number of cycles for the amplitude to halve.
δ = 2π × 0.02 / √(1 − 0.0004) = 0.1257; cycles = ln 2 / 0.1257 = 5.5.
5A 10 kg mass on a 1000 N/m spring has a damper with c = 300 N·s/m. Classify the motion and find the roots of the characteristic equation.
c_c = 200 N·s/m, ζ = 1.5: overdamped. s = 10 (−1.5 ± √1.25) = −3.82 and −26.18 s⁻¹.
6A record shows a peak of 12 mm and, 10 cycles later, 3 mm. Find δ and ζ.
δ = ln 4 / 10 = 0.1386; ζ = 0.1386 / √(4π² + 0.1386²) = 0.0221.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.