6.1 Work of forces and couples
After this lesson you should be able to:
- Define the work done by a force and by a couple, and state when a force does no work.
- Calculate the work of a constant force, of a weight, of a linear spring and of a couple turning through an angle, with correct signs and SI units.
- Separate working forces from non-working forces (reactions at fixed pins, normal forces on fixed smooth surfaces, internal forces of a rigid body) as preparation for the principle of virtual work.
Theory
Up to now equilibrium has been written as ΣF = 0 and ΣM = 0. Energy methods look at the same problems differently: instead of asking which forces balance, they ask how much work the forces would do if the body moved a little. To use them we first need a precise idea of work.
A force F whose point of application moves through a small displacement dr does work dU = F · dr = F ds cos α, where ds is the length of the movement and α is the angle between the force and the movement. Only the component of the force along the path does work. Work is a scalar: positive when the force helps the motion, negative when it opposes it, and zero when the force is perpendicular to the motion or its point of application does not move. Its SI unit is the joule, 1 J = 1 N·m.
Several everyday forces therefore do no work: the reaction at a fixed pin (its point does not move), the normal reaction of a fixed smooth surface (perpendicular to the motion), and the internal forces between particles of a rigid body (they act in equal and opposite pairs on points whose separation does not change). This is what makes energy methods economical: these forces drop out of the equations.
A couple of moment M acting on a body that rotates through a small angle dθ does work dU = M dθ, with θ in radians. The two forces of the couple move in opposite directions by amounts proportional to their distances from the centre of rotation, and their works add up to M dθ whatever the centre. A weight W does work −W Δy when its centre of gravity rises by Δy, and a linear spring of stiffness k does work −½ k (x₂² − x₁²) on the body attached to it when its extension changes from x₁ to x₂.
Derivation
- Constant force: if F is constant in magnitude and direction, U = ∫ F · dr = F · ∫ dr = F · Δr = F d cos α for a straight displacement d.
- Weight: with y measured upwards, the weight is the force (0, −W), so dU = −W dy and U = −W (y₂ − y₁). The work depends only on the change of height, not on the path.
- Linear spring: the spring pulls on the body with force −k x along its axis, where x is the extension. dU = −k x dx, so U = −k ∫ x dx from x₁ to x₂ = −½ k (x₂² − x₁²).
- Couple: let the forces F and −F of a couple act at points A and B a distance d apart, and let the body rotate by dθ about any point O. The displacements of A and B normal to OA and OB have lengths r_A dθ and r_B dθ; the sum of the works is F (r_A − r_B) dθ measured along the common perpendicular, which equals F d dθ = M dθ.
- Couple turning through a finite angle: if M is constant, U = M (θ₂ − θ₁).
dU = F · dr = F ds cos α (J = N·m)Constant force over straight displacement d: U = F d cos αWeight: U = −W Δy (Δy = rise of the centre of gravity)Linear spring (work done by the spring): U = −½ k (x₂² − x₁²); k in N/m, x in mCouple: U = M Δθ (M in N·m, Δθ in rad)In components: U = F_x Δx + F_y Δy for a constant force
- Bodies are rigid unless a spring or other deformable member is named.
- A linear spring obeys F = k x over the whole range considered.
- Angles in the couple formula are in radians.
- Friction is a working force; it does negative work when surfaces slide over each other, and it is included as an applied force when it acts.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- No design code governs this lesson; work and energy are principles of mechanics. Design codes use the results indirectly, for example when loads on members are found by energy methods in structural analysis.
Worked examples
Problem. A crate weighing 2 kN is dragged 15 m along a level floor by a rope inclined at 30° above the horizontal with a tension of 800 N. The coefficient of kinetic friction is 0.4. Find the work done by the rope, by friction, by the weight and by the normal reaction, and the net work.
- Rope: U = 800 × 15 × cos 30° = 10 392 J = 10.39 kJ.
- Normal reaction: N = W − T sin 30° = 2 000 − 400 = 1 600 N. It is perpendicular to the motion, so it does no work.
- Friction: F = 0.4 × 1 600 = 640 N, opposing the motion, so U = −640 × 15 = −9 600 J.
- Weight: the crate does not rise, so U = 0.
- Net work = 10 392 − 9 600 = 792 J; this goes into kinetic energy of the crate (Chapter 8).
Answer. Rope 10.39 kJ; friction −9.60 kJ; weight 0; normal 0; net 792 J
Problem. A linear spring of stiffness 20 kN/m is stretched from an extension of 50 mm to an extension of 150 mm. Find the work done on the spring by the external force and the work done by the spring on the body stretching it.
- k = 20 000 N/m, x₁ = 0.05 m, x₂ = 0.15 m.
- Work done on the spring = ½ k (x₂² − x₁²) = 0.5 × 20 000 × (0.0225 − 0.0025) = 200 J.
- The spring pulls against the stretching, so the work it does on the body is −200 J.
- Note that the work is not k × (change of extension) × average force taken loosely; with the linear law the average force is k (x₁ + x₂)/2 = 2 000 N and 2 000 × 0.10 = 200 J, which agrees.
Answer. 200 J done on the spring; −200 J done by the spring
Problem. A winch drum of radius 0.25 m is turned by a constant torque of 1.2 kN·m through 3 full revolutions, lifting a load on a rope wound on the drum at steady speed. Find the work done by the torque, the height the load rises and the load, ignoring losses.
- Angle turned = 3 × 2π = 18.85 rad.
- U = M Δθ = 1 200 × 18.85 = 22 619 J = 22.62 kJ.
- Rope wound in = r Δθ = 0.25 × 18.85 = 4.712 m, so the load rises 4.712 m.
- At steady speed the work of the torque equals the work against the weight: W × 4.712 = 22 619, so W = 4 800 N, the same as M / r = 1 200 / 0.25.
Answer. U = 22.62 kJ; rise 4.712 m; load 4.8 kN
Step-by-step procedure
- Draw the body and mark every force and couple acting on it.
- Identify the displacement of the point of application of each force (or the rotation for each couple).
- Strike out non-working forces: fixed-pin reactions, normal reactions of fixed smooth surfaces, internal forces of rigid bodies.
- Compute each work term with its sign: F d cos α, −W Δy, −½ k (x₂² − x₁²), M Δθ.
- Add the terms, keeping units in joules.
Site notes
- A winch or chain pulley block multiplies force but not work: the operator always does at least as much work as is needed to lift the load, and friction adds to it.
- Dragging loads with an inclined rope reduces the normal force and hence the friction; on site, a slightly raised pull angle makes skidding heavy items easier.
- Spring buffers, bearings and rubber pads store energy as ½ k x²; doubling the compression stores four times the energy, which is why over-compressed buffers can kick back hard.
- Using degrees instead of radians in U = M Δθ.
- Giving the work of a weight as +W h when the load is raised (the weight does negative work; the lifting device does positive work).
- Using k (x₂ − x₁)² instead of k (x₂² − x₁²) for a spring that starts already stretched.
- Counting the work of a fixed-pin reaction or of a normal force on a fixed smooth surface.
- Mixing kN and N, or mm and m, in the same work term.
Only the component of a force along the movement does work; if a force is perpendicular to the path or its point does not move, its work is exactly zero.
Summary
- dU = F · dr; work is a scalar in joules.
- Weight: −W Δy; spring: −½ k (x₂² − x₁²); couple: M Δθ.
- Fixed-pin reactions, smooth fixed-surface normals and internal forces of rigid bodies do no work.
- These ideas are the basis of virtual work and energy methods.
Practice questions
Tap a question to see the answer.
1A force of 500 N moves its point of application 4 m along a line at 60° to the force. Find the work.
U = 500 × 4 × cos 60° = 1 000 J.
2A load of 3 kN is raised 2.5 m. What work does its weight do?
U = −3 000 × 2.5 = −7 500 J = −7.5 kJ.
3A torque of 250 N·m turns a valve wheel through 90°. Find the work.
U = 250 × π/2 = 392.7 J.
4A spring of stiffness 5 kN/m is compressed from its free length by 80 mm. Find the energy stored.
½ × 5 000 × 0.08² = 16 J.
5A constant force F = (30 i + 40 j) N moves its point by Δr = (2 i − 1 j) m. Find the work.
U = 30 × 2 + 40 × (−1) = 20 J.
6Why does the reaction at a frictionless fixed pin do no work?
Its point of application does not move, so F · dr = 0.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- F. P. Beer, E. R. Johnston, D. F. Mazurek, P. J. Cornwell, B. P. Self, Vector Mechanics for Engineers: Statics and Dynamics, McGraw Hill, 12th edition, 2019.
- R. C. Hibbeler, Engineering Mechanics: Statics, Pearson, 15th edition, 2022 (published 2021).
- J. L. Meriam, L. G. Kraige, J. N. Bolton, Engineering Mechanics: Statics, Wiley, 9th edition, 2018.
- S. Timoshenko, D. H. Young, J. V. Rao, S. Pati, Engineering Mechanics (in SI units), McGraw Hill Education (India), 5th edition, 2013.