1.1 Origin and types of soil
After this lesson you should be able to:
- Describe how soils form from rock by physical and chemical weathering, and distinguish residual from transported soils.
- Name the common transported soil types (alluvial, marine, lacustrine, wind-blown, glacial, colluvial) and the major soil groups met in Indian practice, including black cotton soils (IS 1498 cl. 3.6).
- State the particle-size ranges used in IS 1498:1970 for boulders, cobbles, gravel, sand, silt-size and clay-size particles, and the IS 2720 (Part 4) tests that measure them.
- From a sieve analysis, decide whether a soil is coarse- or fine-grained and whether it is a gravel or a sand, as in IS 1498 cl. 3.1–3.4.
Theory
Soil, for an engineer, is the loose or weakly bonded material above bedrock that can be dug without blasting. It is made of mineral particles, water and air, sometimes with organic matter. Almost all of it comes from rock that has been broken down by weathering, and its engineering behaviour depends strongly on how it formed.
Physical (mechanical) weathering breaks rock into smaller pieces without changing its minerals: daily heating and cooling, wetting and drying, frost in cold regions, growth of salt crystals, root wedging and abrasion by water, wind and ice. It produces gravel, sand and silt-size fragments of the parent rock. IS 1498:1970 cl. 2.3 describes sand and gravel in just this way, as cohesionless aggregates of more or less unaltered rock or mineral fragments.
Chemical weathering changes the minerals themselves: hydrolysis turns feldspars into clay minerals, oxidation produces iron oxides (the red and brown colours of many tropical soils), carbonation dissolves limestone, and leaching removes soluble elements. Its products are clay minerals such as kaolinite, illite and montmorillonite. IS 1498 cl. 2.1 defines clay as an aggregate of microscopic and sub-microscopic particles derived from the chemical decomposition and disintegration of rock constituents, plastic over a moderate to wide range of water content.
Residual soils stay where they formed, above the rock they came from. Their properties usually change gradually with depth, from fully weathered soil to weathered rock to fresh rock, and they may hold relict joints of the parent rock. Laterites and lateritic soils of humid tropical regions are residual soils rich in iron and aluminium oxides.
Transported soils have been moved and deposited by an agent, and the agent sorts them. River (alluvial) deposits form layered sands, silts and clays on flood plains and deltas; marine and lacustrine (lake) deposits are often soft, fine-grained clays; wind-blown (aeolian) deposits include dune sands and silty loess; glacial deposits (till) are unsorted mixtures from boulders to clay; colluvial soils collect at the foot of slopes by gravity. Sorting explains why alluvial sands can be uniform while glacial till is widely graded.
In Indian practice, engineers commonly meet deep alluvium on the great river plains, soft marine clays along the coasts, lateritic soils in high-rainfall regions, wind-blown sands in arid areas and black cotton soils on the basaltic plateau. IS 1498 cl. 3.6 notes that black cotton soils are inorganic clays of medium to high compressibility, predominantly montmorillonitic, black or blackish grey, with high shrinkage and swelling, and that they form a major soil group in India. Highly organic soils such as peat form a separate division (cl. 3.1.3).
For classification, IS 1498 first uses particle size. In our own words, its size ranges (Table 1) are: boulders larger than 300 mm; cobbles from 300 mm down to the 80 mm IS sieve; gravel from 80 mm to 4.75 mm (coarse 80–20 mm, fine 20–4.75 mm); sand from 4.75 mm to 75 µm (coarse 4.75–2.0 mm, medium 2.0 mm–425 µm, fine 425–75 µm); and particles smaller than 75 µm called fines. A note in cl. 3.2.2 adds that particles smaller than 2 µm may be called clay-size and those between 75 µm and 2 µm silt-size, but the standard divides fine-grained soils by plasticity and compressibility, not by size (Chapter 2).
IS 2720 (Part 4):1985 gives the laboratory method: dry sieving for the fraction retained on the 4.75 mm sieve, wet sieving with a dispersing agent for the fraction between 4.75 mm and 75 µm, and sedimentation (pipette as the standard method, hydrometer as a subsidiary method) for the fraction finer than 75 µm, which is used only when enough material passes 75 µm.
Derivation
- Let the oven-dry mass of the sample (after removing particles larger than 80 mm, as in IS 1498 cl. 3.4) be M. Mass retained between two sieves is m_i; percentage of each fraction p_i = 100 m_i / M.
- Gravel fraction = mass retained on the 4.75 mm sieve (and passing 80 mm). Sand fraction = mass passing 4.75 mm and retained on 75 µm. Fines = mass passing 75 µm.
- Coarse fraction = gravel + sand. Division (cl. 3.1.1–3.1.2): coarse-grained if coarse fraction > 50 % of M; otherwise fine-grained.
- Subdivision of a coarse-grained soil (cl. 3.2.1): gravel if more than half the coarse fraction is retained on 4.75 mm, i.e. gravel/(gravel + sand) > 0.5; otherwise sand.
- Fines content decides clean or dirty (cl. 3.4.1, applied to sands by 3.4.2): fines < 5 % clean; fines > 12 % dirty (GM/GC or SM/SC by plasticity); 5–12 % boundary classification.
p_i = 100 m_i / M (percent by dry mass)Coarse-grained if (gravel + sand) > 50 %; fine-grained if fines ≥ 50 % (IS 1498 cl. 3.1)Gravel if gravel / (gravel + sand) > 0.5; else sand (cl. 3.2.1)Fines < 5 %: clean; 5–12 %: boundary; > 12 %: dirty (cl. 3.4.1)Size limits (IS 1498, Table 1 ranges): 300 mm, 80 mm, 20 mm, 4.75 mm, 2.0 mm, 425 µm, 75 µm; 2 µm silt/clay-size note (cl. 3.2.2)
- Masses are oven-dry and the sample is representative of the layer; particles above 80 mm are removed and recorded separately (IS 1498 cl. 3.4).
- Percentages in the examples are by dry mass of the fraction smaller than 80 mm.
- Silt-size and clay-size percentages in Example 2 come from a sedimentation test (IS 2720 Part 4 cl. 5) and are given data; IS 1498 classifies fines by plasticity, so the final group symbol needs Atterberg limits (Chapter 2).
- Descriptions of weathering and deposits are general geology for learning; a real site needs investigation, boreholes and testing.
Codes and standards
Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.
- IS 1498:1970 cl. 1.1 (scope, guidance), 2.1–2.3 (clay, silt, sand and gravel), 3.1.1–3.1.3 (three divisions), 3.2.1–3.2.2 (subdivisions; 2 µm size note), 3.4 and 3.4.1–3.4.2 (field identification; clean, dirty and boundary fines limits), 3.6 (black cotton soils), Table 1 (size ranges, paraphrased).
- IS 2720 (Part 4):1985 cl. 1.1 (scope), 3 (dry sieving of fraction retained on 4.75 mm), 4 and 4.3.1 (wet sieving of fraction between 4.75 mm and 75 µm), 5 (analysis of fraction passing 75 µm; pipette standard, hydrometer subsidiary).
- ASTM D2487 (Unified Soil Classification System) and EN ISO 14688-1 are named for comparison; each uses its own size limits and is applied within its own system.
Worked examples
Problem. An oven-dry sample of 1 000 g (all passing 80 mm) gives these masses retained: 20 mm sieve 50 g; 4.75 mm 150 g; 2.0 mm 120 g; 425 µm 200 g; 75 µm 230 g; passing 75 µm (pan, after wet sieving) 250 g. Find the gravel, sand and fines percentages, the sub-fractions, and the IS 1498 division and subdivision.
- Check total: 50 + 150 + 120 + 200 + 230 + 250 = 1 000 g.
- Gravel = 50 + 150 = 200 g = 20.0 % (coarse 5.0 %, fine 15.0 %).
- Sand = 120 + 200 + 230 = 550 g = 55.0 % (coarse 12.0 %, medium 20.0 %, fine 23.0 %).
- Fines = 250 g = 25.0 %.
- Coarse fraction = 20.0 + 55.0 = 75.0 % > 50 %, so the soil is coarse-grained (cl. 3.1.1).
- Gravel share of coarse fraction = 200 / 750 = 0.267 < 0.5, so it is a sand (cl. 3.2.1).
- Fines 25.0 % > 12 %, so it is a dirty sand: SM or SC, decided by the plasticity of the fines (Chapter 2).
Answer. Gravel 20 %, sand 55 %, fines 25 %: coarse-grained dirty sand (SM or SC after plasticity test)
Problem. For the soil of Example 1, a sedimentation test (IS 2720 Part 4 cl. 5) on the fines shows that 60 g of the 1 000 g sample is finer than 2 µm. (a) Find the silt-size and clay-size percentages and check that all fractions add to 100 %. (b) On site, a different sample weighs 2.40 kg after removing 0.30 kg of cobbles; by eye, about 1.10 kg of it is visible particles. Is it coarse- or fine-grained by the IS 1498 field method?
- (a) Clay-size = 60 / 1 000 = 6.0 %.
- Silt-size = 25.0 − 6.0 = 19.0 %.
- Total = 20.0 + 55.0 + 19.0 + 6.0 = 100.0 % (check).
- Note: these size fractions describe texture only; IS 1498 names fine-grained groups by plasticity, not by the 2 µm split (cl. 3.2.2 note).
- (b) Particles larger than 80 mm (the cobbles) are removed before classifying (cl. 3.4); fraction classified = 2.40 kg.
- Visible particles = 1.10 / 2.40 = 45.8 % < 50 %, so by the field method it is fine-grained (cl. 3.4). Confirm with a laboratory sieve test.
Answer. (a) Silt-size 19 %, clay-size 6 %, total 100 %; (b) 45.8 % visible particles: fine-grained
Step-by-step procedure
- Read the geological map and any earlier borelogs to know whether residual, alluvial, marine or other deposits are expected.
- Describe each layer in the field: colour, moisture, consistency or density, structure, odour (organic), and visible particle content (IS 1498 cl. 3.4).
- Take representative samples; remove and record particles over 80 mm.
- In the laboratory, carry out sieve analysis (IS 2720 Part 4 cl. 3–4) and, where enough fines pass 75 µm, sedimentation (cl. 5).
- Compute gravel, sand and fines percentages; decide coarse- or fine-grained and gravel or sand (IS 1498 cl. 3.1–3.2).
- For fines, add Atterberg limits and complete the group symbol (Chapter 2); add a word description with the deposit type.
Site notes
- Expect layering in alluvial and marine deposits: a thin soft clay band between sands can control settlement and stability.
- Treat black cotton soils with care: they shrink and swell with moisture change (IS 1498 cl. 3.6); foundations need depth, moisture control or special measures set by the designer.
- Residual soils can hide boulders (corestones) and relict joints; trial pits often explain more than a single borehole.
- Peat and highly organic soils compress greatly and should be identified early (cl. 3.1.3).
- Sampling pits and trenches are excavations: support or batter them and keep people out of unsupported trenches. This lesson is educational, not a site procedure.
- Calling every fine-grained soil "clay" from its colour or feel without a plasticity test.
- Using the 2 µm clay-size percentage alone to name a soil, when IS 1498 groups fines by plasticity.
- Forgetting to remove particles over 80 mm before computing percentages.
- Dividing the gravel by the total mass, instead of by the coarse fraction, when deciding gravel versus sand (cl. 3.2.1).
- Treating a transported deposit as uniform with depth without checking for layers.
- Mixing size limits from different classification systems in one calculation.
IS 1498: coarse-grained if more than half is larger than 75 µm; then gravel if more than half the coarse fraction is larger than 4.75 mm, else sand; fines < 5 % clean, > 12 % dirty, 5–12 % boundary. Sizes: 300 / 80 / 4.75 mm / 75 µm (2 µm note).
Summary
- Soils form from rock by physical weathering (fragments of unaltered rock: gravel, sand, silt) and chemical weathering (new clay minerals).
- Residual soils lie over their parent rock; transported soils are sorted by rivers, sea, lakes, wind, ice or gravity.
- Black cotton soils are montmorillonitic inorganic clays with high shrinkage and swelling and form a major Indian soil group (IS 1498 cl. 3.6).
- IS 1498 size ranges: boulder > 300 mm, cobble 300–80 mm, gravel 80–4.75 mm, sand 4.75 mm–75 µm, fines < 75 µm.
- Classification starts with grain size (IS 2720 Part 4 tests) and, for fines, continues with plasticity in Chapter 2.
Practice questions
Tap a question to see the answer.
1Which kind of weathering produces clay minerals?
Chemical weathering (hydrolysis, oxidation, leaching); IS 1498 cl. 2.1 describes clay as derived from chemical decomposition and disintegration of rock constituents.
2Give the IS 1498 size range for sand and its three sub-divisions.
4.75 mm to 75 µm; coarse 4.75–2.0 mm, medium 2.0 mm–425 µm, fine 425–75 µm.
3A soil has 30 % gravel, 25 % sand and 45 % fines. Coarse- or fine-grained? Gravel or sand?
Coarse fraction 55 % > 50 %: coarse-grained; gravel share 30/55 = 0.545 > 0.5: gravel; fines 45 % > 12 %: dirty gravel (GM or GC).
4A sand has 8 % fines. How is it classified for cleanliness?
Between 5 % and 12 %: boundary classification (dual symbol) per IS 1498 cl. 3.4.1–3.4.2.
5Which IS 2720 (Part 4) method is standard for the fraction finer than 75 µm?
The pipette method; the hydrometer method is subsidiary.
6Why is glacial till usually widely graded while dune sand is uniform?
Ice carries and drops all sizes together without sorting; wind sorts particles by size, leaving a narrow range.
References
Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.
- K. Terzaghi, R. B. Peck, G. Mesri, Soil Mechanics in Engineering Practice, John Wiley and Sons, 3rd edition, 1996.
- R. F. Craig, Craig's Soil Mechanics, Spon Press, 8th edition, 2012.
- B. M. Das, Principles of Geotechnical Engineering, Cengage Learning, 9th edition, 2017.