Indiacon CivilSubscribe

Textbook › Surveying › Chapter 1 › Lesson 1.3

1.3 Maps, scales and coordinate systems

Surveying Chapter 1: Fundamentals Under review — not yet three-checked Author: Indiacon

Learning objectives

After this lesson you should be able to:

  • Define the representative fraction (RF) of a map, convert it to a statement scale, and compute a ground length from a map length, and the reverse.
  • Use the square of the RF to convert a map area to a ground area, including hectares and square kilometres.
  • Compute the new RF of a paper map that has shrunk uniformly, from a line whose original and shrunk map lengths are known.
  • Distinguish geographic coordinates on a stated ellipsoid from plane (projected) coordinates, naming the official WGS 84 semi-major axis already used in Lesson 1.1, without inventing a national-grid parameter.

Theory

A map is a reduced drawing of a portion of the Earth, and the scale of that drawing is the first number a surveyor must be able to read. Lesson 1.1 distinguished plane from geodetic work by the size of the curvature effect; this lesson is about how positions and lengths, once they have been determined, are written on a plan or in a coordinate list. Errors and their adjustment were Lesson 1.2. The chain, the compass and the level, which produce the lengths and the heights that the map records, begin in Chapters 2 and 3.

The representative fraction is the ratio of a length on the map to the corresponding length on the ground, expressed in the same unit, and written as 1 : N or as the fraction 1/N. A scale of 1 : 50 000 means that 1 mm on the map represents 50 000 mm, which is 50 m, on the ground; equivalently, 1 m on the map represents 50 000 m on the ground. The same ratio can be written as a statement scale, “1 cm to 500 m”, or shown as a graphical bar that remains true if the paper is later photocopied or shrunk, because the bar shrinks with the map. A large RF (for example 1 : 1 000) is a large-scale map, on which a given ground length occupies more paper; a small RF (for example 1 : 250 000) is a small-scale map. The words “large” and “small” refer to the fraction, not to the second number in 1 : N, and they are not a ranking of the usefulness of the two maps. Areas scale as the square of the RF. If the RF is 1 : N, one unit of area on the map represents N² units of area on the ground, in the same unit. In SI-related area units used in civil work, 1 hectare is 10 000 m² and 1 km² is 100 ha. Those two relations are used in the examples; they are not a substitute for a project’s stated unit.

Maps, scales and coordinatesmap lengthground lengthRF = map length / ground lengthsame units; 1:50 000 means 1 mm to 50 m1 cm² on a 1:50 000 map= 500 m × 500 m = 0.25 km²area scale is (RF)²; 1 ha = 10 000 m²Indiacon original, not to scale
Figure 1.3: Representative fraction as a map length against a ground length, and the area represented by one square centimetre on a 1 : 50 000 map. Indiacon original, not to scale.

Paper maps shrink and stretch with moisture and handling. If a line that was drawn at a known original scale has a new, shorter map length after shrinkage, the ground length has not changed, so the RF has changed. The new representative fraction is the new map length divided by the same ground length, or, equivalently, RF_new = RF_old × (new map length / original map length). The correction is for uniform shrinkage along the line that was re-measured. It is not a claim that every paper map shrinks equally in both directions, and it does not apply to a digital map, whose scale is a display setting rather than a property of a sheet. A graphical scale bar, drawn on the original sheet, remains usable after uniform shrinkage; a written 1 : N taken from the title box does not, unless it is updated as above.

Positions may be stated as geographic coordinates (latitude and longitude) on a stated reference ellipsoid, or as plane coordinates (eastings and northings, or a local x, y) on a projected or assumed plane. Lesson 1.1 already used the official WGS 84 semi-major axis a = 6 378 137 m exactly, from the NIMA / NGA WGS 84 technical literature, as a check on the spherical sagitta. The same ellipsoid is a common reference for geographic coordinates. A projection takes a portion of that ellipsoid, or of a sphere, onto a plane so that a limited survey can be computed with plane trigonometry. The numerical constants of a particular projection — a false easting, a central-meridian scale factor, an Indian national belt origin — are part of a stated coordinate reference system and are not quoted in this lesson, because official texts of those Indian parameters were not on the box at writing. A site survey that uses a local assumed origin and an assumed north is a plane coordinate system of the same kind; it is adequate only when it has been connected, or can be connected, to the project or national framework, as Lesson 1.1 required. The choice of system is a project decision, not a ranking of geographic coordinates against plane coordinates.

Derivation

  1. RF = (map length) / (ground length), with both lengths in the same unit. If the RF is 1 : N, then ground length = N × map length, and map length = (ground length) / N.
  2. A statement scale is the same ratio in convenient units. For 1 : 50 000, 1 mm on the map is 50 000 mm = 50 m on the ground, or 1 cm on the map is 500 m on the ground.
  3. Areas: a square of map side ℓ represents a square of ground side N ℓ, so the area ratio is N². For 1 : 50 000, 1 cm on the map is 500 m on the ground, and 1 cm² on the map is 500 × 500 = 250 000 m² = 0.25 km² = 25 ha, using 1 ha = 10 000 m² and 1 km² = 1 000 000 m² = 100 ha.
  4. Shrinkage: the ground length is fixed by the original construction, L = N_old × (original map length). After shrinkage, N_new = L / (new map length) = N_old × (original map length) / (new map length).
  5. Geographic coordinates are angular positions on a stated ellipsoid. Plane coordinates are lengths on a stated (or assumed) plane. No projection constants are derived here.
Formulas, symbols and SI units
  • RF = map length / ground length (same units), written 1 : N or 1/N
  • Ground length = N × map length; map length = ground length / N
  • 1 : 50 000 means 1 mm on the map = 50 m on the ground, or 1 cm on the map = 500 m on the ground
  • Area on the ground = (area on the map) × N² (same unit); for mixed units, convert first
  • 1 ha = 10 000 m²; 1 km² = 100 ha = 1 000 000 m²
  • After uniform shrinkage along a line: N_new = N_old × (original map length) / (new map length)
  • WGS 84 semi-major axis, as in Lesson 1.1: a = 6 378 137 m exactly, named as an official ellipsoidal reference, not as a map scale
Assumptions and limits
  • The RF applies to lengths in the plane of the map. It does not, by itself, convert a slope distance on the ground; slope reduction is a field correction and is not computed here.
  • The area factor N² assumes that the same RF applies in both directions of the plan. A map that has shrunk unequally in the two directions needs two scale checks.
  • The shrinkage formula is for a uniform change of the paper along the line that was re-measured, with the ground length unchanged. It is not used on a digital display.
  • The hectare and square-kilometre relations are the ordinary SI-related area units used in the examples. A project that states another unit (for example a local customary unit) must be converted explicitly.
  • No Indian national-grid or Survey of India sheet constant is used. Official texts of those parameters were not on the box at writing, so they are not invented.
  • The WGS 84 semi-major axis is the official figure already used in Lesson 1.1. It does not, by itself, fix a projection.
  • This lesson does not construct a diagonal scale as a drawing, does not specify a map series, and does not copy a textbook figure.

Codes and standards

Indian Standards are cited by number and clause only; no clause text, tables or figures are reproduced. Other standards are listed for comparison, not ranked.

  • BIPM, The International System of Units (SI Brochure), 9th edition, 2019 — metre and the ordinary relation 1 ha = 10 000 m² used as an SI-related area unit in the examples.
  • NIMA / NGA, World Geodetic System 1984 — official semi-major axis a = 6 378 137 m exactly, as already used in Lesson 1.1, named as an ellipsoidal reference for geographic coordinates.
  • No Indian Standard clause and no Survey of India sheet specification is cited. Official texts of those documents were not on the box at writing.
  • Background textbooks, not ranked, editions as in the site references register: S. K. Duggal, Surveying, Vol. 1, McGraw Hill Education (India), 4th edition, 2013; B. C. Punmia, A. K. Jain, A. K. Jain, Surveying, Vol. 1, Laxmi Publications, 17th edition, 2016; C. D. Ghilani, Elementary Surveying: An Introduction to Geomatics, Pearson, 16th edition, 2022 (published 2021).

Worked examples

Example 1 (illustrative): representative fraction and a map length

Problem. A plan is drawn at a scale of 1 : 50 000. (a) Write the corresponding statement scale in the form “1 cm to … m”. (b) A road centre-line measures 64 mm on the plan. What is the ground length, in metres and in kilometres? (c) A pipeline 2.50 km long is to be shown on a plan at 1 : 25 000. What length should it have on the plan, in millimetres?

  1. At 1 : 50 000, 1 cm on the map is 50 000 cm = 500 m on the ground. The statement scale is “1 cm to 500 m”.
  2. 64 mm = 0.064 m on the map. Ground length = 0.064 × 50 000 = 3 200 m = 3.20 km. Equivalently, 1 mm on this map is 50 m on the ground, so 64 mm is 64 × 50 = 3 200 m.
  3. 2.50 km = 2 500 m. At 1 : 25 000, map length = 2 500 / 25 000 = 0.10 m = 100 mm. A 100 mm line on that plan is the 2.50 km pipeline.

Answer. Statement scale 1 cm to 500 m; ground length 3 200 m (3.20 km); plan length 100 mm.

Example 2 (illustrative): area on a map, and a shrunk sheet

Problem. (a) On a 1 : 50 000 map, a reservoir outline encloses 1.00 cm² of paper. What ground area is that, in square metres, in hectares and in square kilometres? (b) A plan was drawn at 1 : 10 000. A line that was 200 mm on the original plan now measures 196 mm after the paper has shrunk. What is the new representative fraction, written 1 : N with N to the nearest integer?

  1. At 1 : 50 000, 1 cm on the map is 500 m on the ground, so 1 cm² on the map is 500 × 500 = 250 000 m².
  2. 1 ha = 10 000 m², so 250 000 m² = 25 ha. 1 km² = 1 000 000 m² = 100 ha, so 250 000 m² = 0.25 km². The three figures are the same area.
  3. The ground length represented by the original 200 mm line is 0.200 × 10 000 = 2 000 m. After shrinkage the map length of that same ground line is 0.196 m, so N_new = 2 000 / 0.196 = 10 204.08…, or 1 : 10 204 to the nearest integer.
  4. Equivalently, N_new = 10 000 × (200 / 196) = 10 000 × 1.020408 = 10 204, the same result. The title-box scale 1 : 10 000 is no longer the scale of the shrunk sheet; a graphical bar drawn on the original sheet would have shrunk with it and would still be readable.

Answer. 1.00 cm² represents 250 000 m² = 25 ha = 0.25 km². The shrunk plan is at 1 : 10 204.

Step-by-step procedure

  1. Read the stated RF, or the statement scale, or the graphical bar, before taking any length off the map. If the sheet may have shrunk, prefer the graphical bar, or re-establish N from a line of known ground length.
  2. Convert the map length and the ground length into the same unit before applying RF = map / ground, or ground = N × map.
  3. For an area, convert with N², or form the ground sides first and multiply. Then, if required, convert square metres to hectares (divide by 10 000) or to square kilometres (divide by 1 000 000).
  4. If a paper plan has shrunk, measure a line whose original map length (or whose ground length) is known, and compute N_new as above. Do not keep using the title-box 1 : N on a shrunk sheet.
  5. State the coordinate system with the data: geographic coordinates with the ellipsoid (for example WGS 84), or plane coordinates with the origin, the axis directions and, if a named projection is used, the name of that system. Do not invent a false easting or a belt constant that has not been taken from the project or from an official text.
  6. A local site grid should be tied, or be capable of being tied, to the project or national framework (Lesson 1.1). Record the origin and the assumed north.
  7. Do not scale a slope distance off a map and call it a horizontal ground length without the slope correction, which is a field reduction, not a scale conversion.

Site notes

  • A photocopied or printed plan often has a slightly different scale from the CAD file it came from. Check a known line, or the scale bar, before setting out from the paper.
  • On a 1 : 50 000 sheet, 0.5 mm of pencil thickness is 25 m on the ground. Do not pretend to read a setting-out to a metre from that sheet.
  • Areas taken from a small-scale map are for planning. A land transfer, a cut-and-fill bill, or a reservoir capacity needs a survey at a scale and an accuracy matched to that purpose (Lesson 1.1).
  • If two drawings of the same site use different local origins, a length scaled on one will not plot on the other until the origins are related. Write the origin on both sheets.
  • A digital map can be zoomed; that does not change the accuracy of the data. Zooming a 1 : 50 000 source to look like 1 : 1 000 does not make it a 1 : 1 000 survey.
  • Geographic coordinates without a stated ellipsoid, or plane coordinates without a stated origin, cannot be reused on the next contract.
Common mistakes
  • Treating 1 : 50 000 as “1 mm to 50 000 m”, or as “1 cm to 50 m”, instead of 1 mm to 50 m (or 1 cm to 500 m).
  • Converting an area with N instead of N², or mixing centimetres on the map with metres on the ground without conversion.
  • Calling 1 : 250 000 a large-scale map because 250 000 is a large number. The RF 1/250 000 is a smaller fraction than 1/1 000, so 1 : 250 000 is the smaller scale.
  • Using the title-box 1 : N on a shrunk or stretched paper plan, without checking a known line or the graphical bar.
  • Scaling a slope distance off the plan and adopting it as a horizontal length, or quoting an area in “cm² on the map” as if it were a ground area.
  • Inventing a national-grid false easting, belt, or scale factor that has not been read in an official text or in the project specification.
  • Ranking geographic coordinates against plane coordinates, or ranking one textbook’s scale chapter against another.
Quick check

RF = map/ground (same units), written 1 : N. Ground length = N × map length. Areas scale as N². 1 ha = 10 000 m², 1 km² = 100 ha. After uniform shrinkage, N_new = N_old × (old map length)/(new map length). State the ellipsoid or the plane origin with the coordinates; do not invent grid constants.

Summary

  • The representative fraction is the ratio of a map length to the corresponding ground length in the same unit, written 1 : N. A 1 : 50 000 map has a statement scale of 1 cm to 500 m.
  • Ground lengths are obtained by multiplying the map length by N. Ground areas are obtained by multiplying the map area by N², then converting, if required, with 1 ha = 10 000 m² and 1 km² = 100 ha.
  • A uniformly shrunk paper plan has a new RF, N_new = N_old × (original map length) / (new map length). A graphical scale bar shrinks with the sheet; a written 1 : N in the title box does not.
  • Geographic coordinates need a stated ellipsoid (WGS 84, with official a = 6 378 137 m, is one such reference). Plane coordinates need a stated origin and axes. Projection constants are not invented in this lesson.
  • No Indian Standard clause and no Survey of India sheet specification is cited, because official texts of those documents were not on the box at writing.

Practice questions

Tap a question to see the answer.

1A map is at 1 : 2 500. A boundary measures 40 mm on the map. What is the ground length?

40 mm = 0.040 m; ground length = 0.040 × 2 500 = 100 m. Equivalently, 1 mm represents 2.5 m, so 40 mm represents 100 m.

2Write the statement scale, in the form “1 cm to … m”, for a 1 : 25 000 map.

1 cm on the map is 25 000 cm = 250 m on the ground, so “1 cm to 250 m”.

3On a 1 : 10 000 plan, a plot measures 4.00 cm². What is the ground area, in square metres and in hectares?

1 cm on the map is 100 m on the ground, so 1 cm² is 10 000 m² = 1 ha. Then 4.00 cm² is 40 000 m² = 4.00 ha.

4A 1 : 5 000 plan shrinks so that a 100 mm original line now measures 98 mm. What is N_new, to the nearest integer?

N_new = 5 000 × (100 / 98) = 5 102.04…, or 1 : 5 102.

5Why does a graphical scale bar remain usable after uniform shrinkage of the sheet, while a written 1 : 50 000 in the title box does not?

The bar is a drawn map length that represents a stated ground length; it shrinks in the same ratio as the rest of the plan, so the RF it displays remains correct. The written 1 : 50 000 is a number on the title box and does not change when the paper shrinks.

6What official length is the WGS 84 semi-major axis, and why is it named in this lesson?

6 378 137 m exactly. It is the official ellipsoidal parameter already used in Lesson 1.1, and it is named here as a reference ellipsoid on which geographic coordinates may be stated, not as a map scale or as a national-grid constant.

References

Standard texts, listed in no order of merit. Our explanations, examples and diagrams are original; nothing is copied from these books.

  • S. K. Duggal, Surveying, Vol. 1, McGraw Hill Education (India), 4th edition, 2013.
  • B. C. Punmia, A. K. Jain, A. K. Jain, Surveying, Vol. 1, Laxmi Publications, 17th edition, 2016.
  • C. D. Ghilani, Elementary Surveying: An Introduction to Geomatics, Pearson, 16th edition, 2022 (published 2021).
  • BIPM, The International System of Units (SI Brochure), 9th edition, 2019, and the ordinary relation 1 ha = 10 000 m². NIMA / NGA, World Geodetic System 1984, official semi-major axis a = 6 378 137 m exactly, as in Lesson 1.1.
Suggest a correction

If something on this page is wrong, tell the editor. Your message is sent privately and is not published.

Sent privately to the Indiacon editor; not published.